The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f6e0f57be0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No 'PKG_CPE_ID' is stored for the kernel package Makefile. This commit
adds this.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit 112f594042)
A lot of recent commits in odhcpd main branch are structural/semantic
changes, so instead of adding those changes to 24.10 branch it's better
to focus on the fixes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
b14cf98 router: log “Sending a RA on lan” at LOG_DEBUG
c2810fe odhcpd: update cmake file
8c2c065 odhcpd: convert README to markdown
3b96480 odhcpd: allow the use of an alternative cfg file
7328bfe odhcpd: remove confusing #defines
cdb9e5b odhcpd: improve RFC9096 § 3.5 SLAAC compliance
RFC9096 § 3.5 SLAAC compliance introduces a new config option (odhcpd
piofolder), which may wear out the flash under certain conditions (for
example: ISPs with dynamic IPv6 prefixes which disconnect the clients
every X hours).
Therefore, setting "dhcp.odhcpd.piofolder" to persistent storage in the
router flash is not advisable and should be set to other kinds of
persistent storage such as USBs, SDs, NVMEs...
In order to prevent wearing out the router flash it's set to ephemeral
storage by default (tmp):
uci set dhcp.odhcpd.piofolder="/tmp/odhcpd-piofolder"
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit ea79b5875a)
2859741d971e dhcpv4: store reqopts as uint8_t
6d342cc03bf7 odhcpd: add DNR (RFC 9463) support
c89b8b3f2ff3 odhcpd: make the IPv6 RA DNR lifetime configurable
066b3dc6ec1a netlink: fix a memory leak
171140e90b6a odhcpd: add a helper function for addr6/prefix parsing
5585b969c18f router: move pref64 calculations to the config stage
4308384748be dhcpv6: add ipv6 pxe support
6e1ad492cef5 router: replace ssize_t with size_t
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit a6da0e0d37)
b462895d3157 lua: CMakeLists: drop redundant cmake_minimum_required
f247c18f8a55 examples: CMakeLists: drop redundant cmake_minimum_required
83a70399030d github: add CI build
d31effb4277b ubusd: Fix out of bounds access in event register message
d95837b1b143 ubusd: acl: compare uid/gid instead of user/group strings
b81257bb20dd ubusd: load extra group IDs for a client process
7d7b45fea05b add debian/ directory
aa4a7ee1d341 ubusd: fix more instances of missing length checks for patterns
60e04048a0e2 ubusd: fix ACL check for receiving events
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4b907e69ea)
2b69c9859946 examples: CMakeLists: update cmake minimum required version to 3.10
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 88fe81bb0c)
Current PKG_MIRROR_HASH is wrong, but it went unnoticed, because the
tarball is being fetched from @OPENWRT project mirrors. Can be
reproduced with:
make package/ebtables/{download,check} FIXUP=1 DL_DIR=/tmp PKG_MIRROR_HASH=''
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/20322
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7d4edb21b6)
Use the copy_from_user() and copy_to_user() functions for accessing
memory provided by the user in the ptm netdev iotls.
In addition also check for root permission before executing ioctl.
Suggested-by: Stanislav Fort from Aisle Research
Reported-by: Stanislav Fort from Aisle Research
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2a76abc544)
NULL and fixed addresses are constant, const qualifier are useless.
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:47:1: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
47 | const void (*ifx_bsp_basic_mps_decrypt)(unsigned int addr, int n) = NULL;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:246:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
246 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf0017c4;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:249:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
249 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf001ea4;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:252:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
252 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf001f38;
| ^~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ac8e876a6e)
Signed-off-by: Nora Matthias Schiffer <neocturne@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/20440
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PCI_IRQ_LEGACY was renamed to PCI_IRQ_INTX for kernel 6.10. Fix
compilation error:
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/vrx518_ep-2.1.0/ep.c:469:69: error: 'PCI_IRQ_LEGACY' undeclared (first use in this function); did you mean 'NR_IRQS_LEGACY'?
469 | err = pci_alloc_irq_vectors(pdev, nvec, nvec, PCI_IRQ_MSI | PCI_IRQ_LEGACY);
| ^~~~~~~~~~~~~~
| NR_IRQS_LEGACY
Signed-off-by: Andre Heider <a.heider@gmail.com>
Co-authored-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e80dfdb6c5)
Signed-off-by: Nora Matthias Schiffer <neocturne@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/20440
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building against recent kernel versions (noticed with 6.12) and -Werror
can fail because a macro MAX(a,b) is already defined in minmax.h or
kernel.h before 5.10.
Initially noticed on 6.12, but it now happens after the kernel bump to
6.6.109 as well (upstream commit 6183c65)
In file included from ../mwlwifi-2025.02.06~db97edf2/hif/fwcmd.h:23,
from ../mwlwifi-2025.02.06~db97edf2/core.c:25:
../mwlwifi-2025.02.06~db97edf2/hif/hostcmd.h:1124: error: "MAX" redefined [-Werror]
1124 | #define MAX(a, b) (((a) > (b)) ? (a) : (b))
| ^~~
In file included from usr/include/mac80211-backport/linux/minmax.h:4,
from ./include/linux/kernel.h:27,
from usr/include/mac80211-backport/linux/kernel.h:3,
from ./include/linux/skbuff.h:13,
from usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from usr/include/mac80211-backport/linux/etherdevice.h:3,
from ../mwlwifi-2025.02.06~db97edf2/core.c:18:
./include/linux/minmax.h:315: note: this is the location of the previous definition
315 | #define MAX(a, b) __cmp(max, a, b)
| ^~~
Add a pending upstream patch which replaces the MAX(a,b) macro to avoid
conflicts and allow compilation with 6.12 backports
(cherry picked from commit 822bceb1d1)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20420
Signed-off-by: Robert Marko <robimarko@gmail.com>
This includes the following commits from upstream Linux between 6.12.44
and 6.12.52:
```
$ git log --reverse --oneline v6.12.44...v6.12.52 -- drivers/net/wireless/ net/mac80211/ net/wireless/
5b7ae04969f8 wifi: cfg80211: fix use-after-free in cmp_bss()
3e789f8475f6 wifi: brcmfmac: fix use-after-free when rescheduling brcmf_btcoex_info work
d9f2fb6a2ac8 wifi: mt76: mt7925: fix locking in mt7925_change_vif_links()
1fb26fd3f601 wifi: mt76: prevent non-offchannel mgmt tx during scan/roc
2aef3667e6b0 wifi: mt76: free pending offchannel tx frames on wcid cleanup
e4d5a5fc61fd wifi: mt76: fix linked list corruption
c2e32ac3f107 wifi: iwlwifi: uefi: check DSM item validity
609a8ffff5a0 wifi: ath11k: fix group data packet drops during rekey
cedbbba8a8e8 wifi: cw1200: cap SSID length in cw1200_do_join()
92bedee7168d wifi: libertas: cap SSID len in lbs_associate()
31229145e6ba wifi: cfg80211: sme: cap SSID length in __cfg80211_connect_result()
06616410a3e5 wifi: mwifiex: Initialize the chan_stats array to zero
a001c2f6a40c wifi: mt76: mt7925u: use connac3 tx aggr check in tx complete
eefa2ad9009b wifi: mt76: mt7996: Initialize hdr before passing to skb_put_data()
089fd41902ee wifi: mt76: mt7925: fix the wrong bss cleanup for SAP
26618c039b78 wifi: ath11k: update channel list in reg notifier instead reg worker
fa4abd439f27 wifi: ath11k: update channel list in worker when wait flag is set
2203ef417044 wifi: wilc1000: avoid buffer overflow in WID string configuration
32adb020b0c3 wifi: mac80211: increase scan_ies_len for S1G
8df33f4d4a0b wifi: mac80211: fix incorrect type for ret
79dc6d4932de wifi: virt_wifi: Fix page fault on connect
1f52119809b7 wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
895cccf639ac wifi: rtw89: fix use-after-free in rtw89_core_tx_kick_off_and_wait()
914d02595ba6 wifi: rtlwifi: rtl8192cu: Don't claim USB ID 07b8:8188
1713796d6538 wifi: rtl8xxxu: Don't claim USB ID 07b8:8188
```
Removed ath11k/940-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch
This problem is fixed by:
609a8ffff5a0 wifi: ath11k: fix group data packet drops during rekey
Link: https://github.com/openwrt/openwrt/pull/20311
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenSSL 3.0.18 is a security patch release. The most severe CVE fixed in this
release is Moderate.
This release incorporates the following bug fixes and mitigations:
* Fix Out-of-bounds read & write in RFC 3211 KEK Unwrap. (CVE-2025-9230)
* Fix Out-of-bounds read in HTTP client no_proxy handling. (CVE-2025-9232)
The removed patch is included upstream:
c0d968f0ac
Link: https://github.com/openwrt/openwrt/pull/20312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
(cherry picked from commit b2f814fed4)
Link: https://github.com/openwrt/openwrt/pull/20159
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the MT7628 hardware datasheet:
- GPIO/4 was originally used for I2C, but is now used as the Modem Power.
- GPIO/5 was originally used for I2C, but is now used as the SIM card select. (n/a for this device)
- GPIO/6 was originally used for SPI CS1, but is now used as the Serial mode switch.
- GPIO/36 was originally used for PERST, but is now used as the GPS OE. (n/a for this device)
- GPIO/38 was originally used for WDT, but is now used as the Modem2 Power. (n/a for this device)
- GPIO/44 was used for WLED_AN, but is now controlled by `gpio-leds`.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20256
(cherry picked from commit 44c79d094f)
Link: https://github.com/openwrt/openwrt/pull/20257
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport support for 1024 MPDU TX aggregation in EHT from upstream
kernel. Without this fix, TX performance on WiFi-7 links
is severely limited, making the link practically unusable.
Signed-off-by: Oliver Sedlbauer <osedlbauer@tdt.de>
Make sure that the package gets updated after the last fix.
Fixes: 9d83c1b1a9 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0203ef3fc9)
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cd20ae44f2)
The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
(cherry picked from commit 420be05d90)
Link: https://github.com/openwrt/openwrt/pull/19985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
(cherry picked from commit aea6d1bf5e)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes compilation of the vmmc driver, it uses these functions.
Fixes: c676281e7e ("kernel: bump 6.6 to 6.6.103")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 6690f551c8)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 18925614c0)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
(cherry picked from commit 0e4a69e340)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19928
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a patch from upstream kernel 6.17-rc4 which fixes a regression
introduced in the latest stable kernel versions.
This is already in the Linus stable queues for the next minor kernel
updates.
Fixes: 1c92e468d5 ("kernel: bump 6.6 to 6.6.103")
Fixes: f39c7e103f ("kernel: bump 6.12 to 6.12.43")
Reported-by: Goetz Goerisch <ggoerisch@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c589fb7baf)
8b320f9 ucode: adjust for new ext resource type
e61d2be sys: use strstr() to detect installed packages
bba9519 rpc-sys: packagelist: don't truncate input lines on read
The removed patch was applied upstream.
Link: https://github.com/openwrt/openwrt/pull/19919
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL83xx devices have two types of receive interrupts for each of its
8 rings. One for packet received and another for ring overflow. When
the switch is flooded with incoming packets the receive handler will
disable the packet receive notification but still keeps the overflow
notification enabled. While the receive path "slowly" processes the
received packets each new packet triggers the overflow IRQ again. The
device becomes unresponsive and eventually produces messages like:
[18441.709764] rcu: Stack dump where RCU GP kthread last ran:
[18441.727892] Sending NMI from CPU 1 to CPUs 0:
[18441.742300] NMI backtrace for cpu 0 skipped: idling at 0x8080e994
[18415.251700] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[18415.271350] rcu: 0-...!: (0 ticks this GP) idle=d740/0/0x0 ...
[18415.303046] rcu: (detected by 1, t=6004 jiffies, g=230925, ...
[18415.326095] Sending NMI from CPU 1 to CPUs 0:
[18415.340540] NMI backtrace for cpu 0
Fix this issue by always disabling receive and overflow interrupts at
the same time.
Test with hping3 --udp -p 5021 -d 1400 --flood 192.168.2.72
Before (3sec run):
[183260.324846] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x101, mask: 0x7ffeff
[183260.340524] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x1, mask: 0x7ffeff
[183260.345799] net_ratelimit: 489997 callbacks suppressed
After (3 sec run):
[ 373.981479] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 374.031118] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 377.919996] net_ratelimit: 34 callbacks suppressed
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19365
(cherry picked from commit 963ee6ac3f)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19891
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IgniteNet SunSpot AC Wave2 comes with 2x QCA9994 ath10k chips
connected to the IPQ8068 SoC via PCIe.
Add board-2.bin for both radios on this board.
3ac4a64 qca9984: add BDFs for IgniteNet SS-W2-AC2600
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d8303b4721)
Link: https://github.com/openwrt/openwrt/pull/19902
[Do not add ignitenet_ss-w2-ac2600]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have modified the kernel to setup all "default" consoles,
including serial ports and framebuffers/screens, providing
no console= argument is supplied on the kernel command line.
Adding 'console=tty1' caused the 'default' serial port on
device tree systems to break, as the kernel would not carry
over the settings (like baud rate) from the bootloader.
The system administrator can still force the use of a
specific console by adding their own console= arguments.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("armsr: use console=tty1 to make
console more readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bff179de73)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A previous change added 'console=tty1' to the default kernel command
line on armsr, in order to ensure the framebuffer console is enabled
on systems capable of graphics output.
Unfortunately, this change broke boards that used device tree
(DT) firmware with serial consoles, as the serial console
specified by the system firmware (stdout-path) was no longer
setup by the kernel.
A bit of probing determined that the SPCR (serial port console
direction table) on ACPI systems was preventing Linux from setting
up a default framebuffer console on these systems (which is why
console=tty1 was added).
(The affected ACPI systems are usually VMs using QEMU's
'virt' machine and EDK2 firmware. The firmware on these systems
does not remove the SPCR when a screen is present)
So to ensure all possible systems are setup correctly, we modify
the kernel so all "default" console types (serial and screen)
are setup when no console= arguments are specified on the kernel
command line.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("use console=tty1 to make console more
readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3697022ce3)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6e4ffe2c6657 ucode: add function for getting the number of entries in a snapshot
a62edd89255b ucode: add support for fetching kernel tracepoint events
edeb4d6dc690 udebug-cli: add support for streaming tracing data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 78188ee2bc)
3d953628bf17 udebugd: add support for setting an override config
93f6df0240e5 udebug-cli: add support for overriding config on the command line
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c4e7b9b9b7)
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
(cherry picked from commit 9ce23ac840)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is some confusion in the Git log of this file. Specifically,
the commit message on 7b7f1702 incorrectly indicates that there was
"potential fear" about copyright infringement.
Upon review of this situation, there is, in my opinion, no concern of
copyright infringement here. This is not legal advice; it is my
opinion based of years of work on copyright policy for FOSS.
However, Elliott Mitchell's idea was obviously helpful as inspiration
in writing this script and deserves credit. Ideas alone, however,
are not to my knowledge copyrightable anywhere in the world.
Signed-off-by: Bradley M. Kuhn <bkuhn@sfconservancy.org>
(cherry picked from commit d8e738e5c4)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
(cherry picked from commit 6889ea7b9a)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PR of openwrt:main: https://github.com/openwrt/openwrt/pull/19512
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
(cherry picked from commit 536a25ebf8)
Link: https://github.com/openwrt/openwrt/pull/19536
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628NN
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN [slot not install], 1x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only [antenna not install]
- LED:
System/Power (RUN): GPIO/37 active-low
Modem: GPIO/3 active-low
RF (Modem Signal): GPIO/2 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- Serial / COM: 1X RS232/RS485 on board (GPIO/6 hi:RS485 lo:RS232)
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- PCIe: 1x miniPCIe for modem [slot not install]
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 192.168.8.1 with root password "superzxmn" (SSH Port 22, Telnet Port 5188)
3. Download openwrt firmware on the computer.
4. Use scp or sftp put firmware to board /tmp
5. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h7920-v40-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h7920-v40-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
(cherry picked from commit ebee946227)
Link: https://github.com/openwrt/openwrt/pull/19716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backpot upstream patch for Flow Offload support for AN7581 and refresh
all affected patch. To correctly work a dedicated firmware is needed to
use the dedicated Network Coprocessor (NPU).
This also introduce good cleanup and moves the driver in a dedicated
Airoha directory. While currently not totally usable (due to lack of
firmware blob) this is needed to backport support for external PHY/SFP
support.
Refresh all affected patch.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
(cherry picked from commit ad2077165b)
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This got added in commit 15887235, cherry-picked into the 24.10 branch
as 642b5b61 and was partially lost in a manual patch refresh in
3a2a2c99.
The main branch still contains the full set of rx DMA size changes, so I
assume it was lost by accident.
With rx.dma_size=2K, my TP-Link Archer MR600v2 (MT7621) randomly reboots
due to OOM.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
In the conversion to dts, qca,led-pin was used for both interfaces.
Unfortunately, it's mutually exclusive with gpio-controller which made
it not do anything.
Fixes: 949e1a0 ("mpc85xx: tl-wdr4900: move platform code to dts")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19758
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit cc0ff28f23)
The bootup of the armsr target sometimes failed like this:
```
[ 0.762283] NET: Registered PF_INET6 protocol family
[ 0.791987] workqueue: Failed to create a worker thread: -EAGAIN
[ 0.801986] workqueue: Failed to create a rescuer kthread for wq "mld": -EAGAIN
[ 0.964017] NET: Unregistered PF_INET6 protocol family
```
Increase the maximum number of threads the kernel allows.
Link: https://github.com/openwrt/openwrt/pull/19376
(cherry picked from commit c5330bdf7e)
Link: https://github.com/openwrt/openwrt/pull/19554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
f510d75ff7 nscd: Use time_t for return type of addgetnetgrentX
5aa4bb67b9 resolv: Fix some unaligned accesses in resolver [BZ #30750]
249646f12b Force DT_RPATH for --enable-hardcoded-path-in-tests
697ab62d11 i386: Disable Intel Xeon Phi tests for GCC 15 and above (BZ 31782)
c8cb4d2b86 misc: Add support for Linux uio.h RWF_NOAPPEND flag
712453634c s390x: Fix segfault in wcsncmp [BZ #31934]
7bfc35959d nptl: fix potential merge of __rseq_* relro symbols
d9d019d674 elf: Make dl-rseq-symbols Linux only
bb30bd2162 Linux: Make __rseq_size useful for feature detection (bug 31965)
dc512364e8 resolv: Allow short error responses to match any query (bug 31890)
6cad0f543c resolv: Do not wait for non-existing second DNS response after error (bug 30081)
1bed6acf50 resolv: Track single-request fallback via _res._flags (bug 31476)
0301637b99 linux: Update the mremap C implementation [BZ #31968]
f0e2114535 mremap: Update manual entry
6bb75212e6 Add mremap tests
3ac7ba61d2 Update syscall lists for Linux 6.5
9184c13681 resolv: Fix tst-resolv-short-response for older GCC (bug 32042)
059f82c3b9 Fix name space violation in fortify wrappers (bug 32052)
c005d1bd6f x86: Fix bug in strchrnul-evex512 [BZ #32078]
28f358bc42 support: Add FAIL test failure helper
99ffa84bdc stdio-common: Add test for vfscanf with matches longer than INT_MAX [BZ #27650]
87a1968a72 Make tst-ungetc use libsupport
804d3c8db7 ungetc: Fix uninitialized read when putting into unused streams [BZ #27821]
b9f72bd5de ungetc: Fix backup buffer leak on program exit [BZ #27821]
15ca66303f posix: Use <support/check.h> facilities in tst-truncate and tst-truncate64
f30501ca75 nptl: Use <support/check.h> facilities in tst-setuid3
370be85892 libio: Attempt wide backup free only for non-legacy code
4dd8641461 Add crt1-2.0.o for glibc 2.0 compatibility tests
fa4ad10406 elf: Change ldconfig auxcache magic number (bug 32231)
9423cc5387 nptl: initialize rseq area prior to registration
37ded328c4 nptl: initialize cpu_id_start prior to rseq registration
cf06772360 x86: Avoid integer truncation with large cache sizes (bug 32470)
5c9be512ee x86_64: Sort fpu/multiarch/Makefile
49016f2190 x86_64: Add log2 with FMA
b2a45f1eee x86_64: Add expm1 with FMA
c92946d9b2 x86_64: Add log1p with FMA
58822f954f x86: Check the lower byte of EAX of CPUID leaf 2 [BZ #30643]
7772f9358c elf: Fix slow tls access after dlopen [BZ #19924]
5a64f93365 x86: Only align destination to 1x VEC_SIZE in memset 4x loop
0d14bf0754 sysdeps/x86/Makefile: Split and sort tests
dc1762113d x86_64: Fix missing wcsncat function definition without multiarch (x86-64-v4)
04b8d48432 x86: Improve large memset perf with non-temporal stores [RHEL-29312]
12fec8aae5 x86/string: Fixup alignment of main loop in str{n}cmp-evex [BZ #32212]
48642ef1a5 elf: Avoid some free (NULL) calls in _dl_update_slotinfo
549e7f7c5a elf: Support recursive use of dynamic TLS in interposed malloc
c32fd59314 Fix underallocation of abort_msg_s struct (CVE-2025-0395)
650a0aaaff stdlib: Test using setenv with updated environ [BZ #32588]
f984e2d7e8 assert: Add test for CVE-2025-0395
9ca74b8ad1 AArch64: Improve generic strlen
95aa21432c AArch64: Optimize memset
5fe151d86a AArch64: Remove zva_128 from memset
3de5112326 math: Improve layout of expf data
52c2b1556f AArch64: Add SVE memset
097299ffa9 AArch64: Use prefer_sve_ifuncs for SVE memset
5a08d049dc math: Improve layout of exp/exp10 data
3be3728df2 elf: Ignore LD_LIBRARY_PATH and debug env var for setuid for static
454f24e981 support: Use const char * argument in support_capture_subprogram_self_sgid
4335cd9b58 support: Add support_record_failure_barrier
31fa0f73e2 elf: Test case for bug 32976 (CVE-2025-4802)
ca41fe44a5 x86_64: Fix typo in ifunc-impl-list.c.
ca7e32d024 elf: Fix subprocess status handling for tst-dlopen-sgid (bug 32987)
81f58dd9b7 support: Pick group in support_capture_subprogram_self_sgid if UID == 0
5a6276d97a Fix error reporting (false negatives) in SGID tests
1a0d73a625 pthreads NPTL: lost wakeup fix 2
b5c4727e59 nptl: Update comments and indentation for new condvar implementation
1fa5e51897 nptl: Remove unnecessary catch-all-wake in condvar group switch
44eaf0615d nptl: Remove unnecessary quadruple check in pthread_cond_wait
7625579f11 nptl: Remove g_refs from condition variables
6bac834c5a nptl: Use a single loop in pthread_cond_wait instaed of a nested loop
5765653697 nptl: Fix indentation
8899e89b29 nptl: rename __condvar_quiesce_and_switch_g1
39a80f4035 nptl: Use all of g1_start and g_signals
51210d6496 nptl: PTHREAD_COND_INITIALIZER compatibility with pre-2.41 versions (bug 32786)
879f0ee122 malloc: add indirection for malloc(-like) functions in tests [BZ #32366]
a637f2c42f malloc: obscure calloc use in tst-calloc
21019afe65 malloc: cleanup casts in tst-calloc
6a52d5cab0 posix: Fix double-free after allocation failure in regcomp (bug 33185)
Link: https://github.com/openwrt/openwrt/pull/19551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6953f19 wireless-regdb: Update regulatory info for Indonesia (ID) for 2025
2e8214e wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band for GB
a94f685 wireless-regdb: Update regulatory info for Egypt (EG) for 2024
7628ce2 wireless-regdb: Update regulatory rules for Brazil (BR) on 6GHz
4411b39 wireless-regdb: Update regulatory info for Vietnam (VN) for 2025
490f136 wireless-regdb: Update regulatory info for Estonia (EE) for 2024
c56c663 wireless-regdb: update regulatory rules for Paraguay (PY) on 6 GHz for 2025
5a8ced5 wireless-regdb: Update regulatory info for CEPT countries for 6GHz listed by WiFi Alliance
5fd8ee3 wireless-regdb: update regulatory rules for Bosnia and Herzegovina (BA) for 6 GHz
e05260a wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/19474
(cherry picked from commit 7fe06b7f56)
Link: https://github.com/openwrt/openwrt/pull/19538
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a854d833ea)
5d10084ea885 lib-ucode.c: add #define _GNU_SOURCE
a95364b41d52 udebug-cli: fix terminating uloop
c00eb9b685a8 ucode: use FILE handle for pcap output
4265167cb6e8 ucode: add error reporting to pcap_write
4a908ee731a6 udebug-cli: stop event loop on write failure
6e04f4187231 ucode: use ucv_resource_create_ex for remote rings
c297f04e1852 ucode: drop use ucv_resource_create
f207d37a1055 ucode: add support for specifying ring format
98683a94bcdd ucode: support appending array data, similar to socket.send()
a7ecd483ed38 ucode: allow calling udebug.init() multiple times
d4a4c788c416 ucode: fix allocation size of local ring meta
184706abaf50 ucode: add timestamp argument to foreach()
8442c948c193 ucode: add function for getting ring information
f4958a4c591a ucode: add const entries for enum udebug_format
14d4fec36993 udebug-cli: add logstream command
6ed8536142bb ucode: fix entries/size confusion
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7b0ce213e9)
These instructions are for 64-bit load/store. On ARMv5TE, the CPU
requires addresses to be aligned to 64-bit. When misaligned, behavior is
undefined (effectively either loads the same word twice on LDRD, or
corrupts surrounding memory on STRD).
On ARMv6 and newer, unaligned access is safe.
Removing these instructions for ARMv5TE is necessary, because GCC
ignores alignment information in pointers and does unsafe optimizations
that have shown up as bugs in various places.
This patch was originally added more than 11 years ago in commit b050f87d13,
but got lost 6 years ago, when gcc 9.1 was added in 88c07c6552.
This primarily affects the kirkwood and ixp4xx targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c1c1112006)
**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Cherry-picked from 949d0bd77a
Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
(cherry picked from commit db1de8d21f)
Link: https://github.com/openwrt/openwrt/pull/19391
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The script always gets passed the package name, not the source name.
Optimize for the default case where the package name matches the
filename prefix.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 471fd0a502)
27839f854a58 ubusd: make txq_len field signed
b35b2bc63e8e ubusd: treat EACCES on write like EAGAIN
713e9d19b2b6 ubusd: retry write on EINTR
8bb523ab20e0 ubusd: fix txq_len accounting
b1b783c74742 ubusd: add another tx attempt on enqueueing the first message for a client
5952b48e251c ubusd: do not call socket callback from ubus_msg_send
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 90cd8640bd)
(cherry picked from commit d9cd67b542)
This device is similar to the Cudy TR3000 v1 128MB version.
The difference is that the flash memory is 128mb and the other is 256mb
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Power: 5 VDC, 3 A
Installation:
Cudy has distributed intermediate firmware to make installation easier
1. Go to [Cudy CN official website](https://www.cudy.com/zh-cn/pages/download-center/tr3000-1-0) and download the intermediate firmware
2. Upgrade the intermediate firmware on the page
3. Visit the intermediate firmware 192.168.1.1 webpage and use the sysupgrade image to update
other:
If you fail to flash the device, you can use TFTP to flash back to the original firmware.
1. Ask Cudy CN official customer service for the original firmware
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an recovery.bin firmware file.
Signed-off-by: cheng wang <typedelta@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19167
(cherry picked from commit 594da824a4)
Link: https://github.com/openwrt/openwrt/pull/19348
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Due to a bug, USB is not powered on after boot on hAP ac.
This prevents extroot configurations from working as overlayfs is mounted
before USB device can be powered on. This commit fixes this by enabling USB
in devicetree.
Related discussion links:
- https://forum.openwrt.org/t/usb-power-is-off-on-boot/229007
---
Extroot configuration requires the USB to be powered on before
preinit_main/80_mount_root. Probably the simplest approach is to enable
it in the devicetree. Another approach would be to add a script into
/lib/preinit that will power on USB via /sys/class/gpio/usb-power/value
E.g.
cat /lib/preinit/79_power_on_usb
do_power_on_usb(){
echo '1' > /sys/class/gpio/usb-power/value
}
boot_hook_add preinit_main do_power_on_usb
Signed-off-by: Valeriy Manzhos <manzhos.va@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f7dba4ebbc)
Link: https://github.com/openwrt/openwrt/pull/19334
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 6f8c58bfd8)
[sync uboot defconfigs with 24.10 branch, change apk to opkg]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
1. Power down the router and hold in the Reset button.
2. While holding in the button power up the router again.
3. Hold the button in for 10 seconds and then release.
4. Use your browser to go to 192.168.1.1
5. If you see a GUI that is for flashing firmware then you have the V2 model.
If there is no GUI and the router continues to boot up normally
you have the V1 model.
6. Now use the V2 sysugrade file.
Note: Recovery GUI it can be used to recover from an incorrect firmware flash.
Based on patches adding support for this device by Yannick Chabanois (openmptcprouter)
and Dairyman (ofmodemsandmen)
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18514
(cherry picked from commit c908fc7d95)
Link: https://github.com/openwrt/openwrt/pull/19216
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport some additional upstream patches to resolves some issues when using
dt overlays on gw72xx-0x and gw73xx-0x:
- 6.13-arm64-dts-imx8mm-venice-gw73xx-remove-compatible-in-overlay-files.patch
- 6.12-arm64-dts-imx8mm-venice-gw72xx-remove-compatible-in-overlay-files.patch
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19218
Signed-off-by: Robert Marko <robimarko@gmail.com>
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
+bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
+bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
+bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
+bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
+bootmenu_8=Reboot.=reset
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
+boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
+boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
+boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
+boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
+boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
+ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
+ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
+ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
+ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
+ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
+ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
+ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
+_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
+_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-dsl-danube/drv_dsl_cpe_api-3.24.4.4/src/common/drv_dsl_cpe_os_linux.c:1155:15: error: variable 'ltq_adsl_driver' has initializer but incomplete type
Subject: [PATCH] add missing prototype for IFX_Var_Fifo_getRoom()
Fix build warning on 6.12 kernel:
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/ifxos-ugw_8.5.2.10/src/common/ifx_fifo.c:532:14: error: no previous prototype for 'IFX_Var_Fifo_getRoom' [-Werror=missing-prototypes]
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c:64:15: error: no previous prototype for 'cgu_get_pp32_clock' [-Werror=missing-prototypes]
64 | unsigned long cgu_get_pp32_clock(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c:969:34: error: array type has incomplete element type 'struct of_device_id'
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c:969:34: error: 'ltq_ptm_match' defined but not used [-Werror=unused-variable]
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:1433:34: error: array type has incomplete element type 'struct of_device_id'
This patch fixes various missing-prototypes build warnings on
6.12 kernel:
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_tapi-3.13.0/src/drv_tapi_event.c:2815:13: error: no previous prototype for 'IFX_TAPI_EventWrpBufferPool_ElementCountGet' [-Werror=missing-prototypes]
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_tapi-3.13.0/src/drv_tapi_event.c:2844:13: error: no previous prototype for 'IFX_TAPI_EventWrpBufferPool_ElementAvailCountGet' [-Werror=missing-prototypes]
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_tapi-3.13.0/src/drv_tapi_fxo.c:145:13: error: no previous prototype for 'TAPI_FXO_DAA_Ioctl' [-Werror=missing-prototypes]
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_tapi-3.13.0/src/drv_tapi_fxo.c:291:13: error: no previous prototype for 'TAPI_FXO_SmartSlic_Ioctl' [-Werror=missing-prototypes]
Subject: [PATCH] add missing prototype for ifx_mei_atm_led_blink()
Fix build warning on 6.12 kernel:
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/dsl_cpe_mei-ugw_8.5.2.10/src/drv_mei_cpe_api_atm_ptm_intern.c:658:5: error: no previous prototype for 'ifx_mei_atm_led_blink' [-Werror=missing-prototypes]
658 | int ifx_mei_atm_led_blink(void)
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/dsl_cpe_mei-ugw_8.5.2.10/src/drv_mei_cpe_mei_access_vrx.c:41:15: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/dsl_cpe_mei-ugw_8.5.2.10/src/drv_mei_cpe_mei_access_vrx.c:55:15: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/dsl_cpe_mei-ugw_8.5.2.10/src/drv_mei_cpe_mei_access_vrx.c:63:15: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_mei_access_vrx.c:41:15: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_mei_access_vrx.c:56:15: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
This patch fixes various missing-prototypes build warnings on
6.12 kernel.
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_api_atm_ptm_intern.c:314:5: error: no previous prototype for 'ifx_mei_atm_led_blink' [-Werror=missing-prototypes]
314 | int ifx_mei_atm_led_blink(void)
| ^~~~~~~~~~~~~~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_api_atm_ptm_intern.c:325:5: error: no previous prototype for 'ltq_ifx_mei_atm_showtime_enter_compat' [-Werror=missing-prototypes]
325 | int ltq_ifx_mei_atm_showtime_enter_compat(IFX_uint8_t dslLineNum,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_api_atm_ptm_intern.c:334:5: error: no previous prototype for 'ltq_ifx_mei_atm_showtime_exit_compat' [-Werror=missing-prototypes]
334 | int ltq_ifx_mei_atm_showtime_exit_compat(IFX_uint8_t dslLineNum) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
---
src/drv_mei_cpe_api_atm_ptm_intern.c | 4 ++--
src/drv_mei_cpe_api_atm_ptm_intern.h | 1 +
2 files changed, 3 insertions(+), 2 deletions(-)
--- a/src/drv_mei_cpe_api_atm_ptm_intern.c
+++ b/src/drv_mei_cpe_api_atm_ptm_intern.c
@@ -322,7 +322,7 @@ int ifx_mei_atm_led_blink(void)
int (*ifx_mei_atm_showtime_enter)(struct port_cell_info *, void *) = NULL;
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/drv_vmmc_sig.h:41:45: error: unknown type name 'IFX_TAPI_DRV_CTX_SIG_t'
Subject: [PATCH] fix 'inline' is not at beginning of declaration
Fix build warning on 6.12 kernel:
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:58:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.