This patch is introducing the same header that the other patch
001-ubifs-utils-link-libmissing.a-in-case-execinfo.h-isn.patch
is guarding against missing in musl libc. We need to
mimic that.
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20938
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fortinet FortiWiFi 30E (FWF-30E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 1 GiB (4x Nanya NT5CC256M8IN-D1)
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 5x 10/100/1000 Mbps
- Switch : Marvell 88E6176
- Wireless : Atheros AR9382 2x2 802.11abgn (mini-PCIe)
- LEDs/Keys : 16x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- USB : 1x USB 3.0
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-30E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "r" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:42 (board-info, 0xd880 (hex))
WAN : 70:4C:A5:xx:xx:43
LAN 1 : 70:4C:A5:xx:xx:44
LAN 2 : 70:4C:A5:xx:xx:45
LAN 3 : 70:4C:A5:xx:xx:46
LAN 4 : 70:4C:A5:xx:xx:47
Signed-off-by: Jimmy Cavanaugh <jamie@cavanaugh.co.nz>
Link: https://github.com/openwrt/openwrt/pull/20787
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If board_detect is interrupted by cutting power on first boot,
board.json might only be half-way written and the file will not be
written again correctly on subsequent boots.
Write to a temporary file first, then rename. Since a rename on the same
file system is an atomic operation, it ensures that either
/etc/board.json does not exist or that the complete file exists.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20831
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* SC2166 (warning): Prefer [ p ] && [ q ] as [ p -a q ] is not well
defined.
* SC2086 (info): Double quote to prevent globbing and word splitting.
* SC2091 (warning): Remove surrounding $() to avoid executing output
(or use eval if intentional).
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20831
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no reason to limit USB to 2.0 mode by default. This
limitation should be done when both gmac2 and USB are enabled.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Remove I2C, PCIe, PWM, UART and USB from the MT7987A SoC dtsi.
These should not be enabled by default, but rather enabled based
on the device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The D-Link DNS-325 A1 is NAS with 2x HDD (3.5 inch) bays, 1x 10/100/1000Base-T port and 1x USB 2.0 port
Device specification:
SoC: Marvell 88F6281-A1 1.2 GHz
RAM: 256 MB (2xSEC K4T1G084QF-HCF7:128Mx8 @400 CL6)
Flash: 128 MB (SAMSUNG 946 K9F1G08U0B PCB0)
SATA: 2x internal SATA II drives
Ethernet: 1x Gigabit (Marvell 88E1116R-NNC1)
LED: 7x (white: Power, white/red: Right SATA Activity, USB Activity, Left SATA Activity)
Key: 3x (Power, Reset, USB Copy/Unmount)
Serial: 5 pin header (RXD,GAP,3.3V,GND,TXD), (115200,8,N,1), 3.3V TTL
USB ports: 1x USB 2.0
Flash instruction:
NOTE: this process uses a serial connection. It will upgrade the bootloader and reset the bootloader environment variables
USB flash stick setup
Format to FAT32 without mbr
Copy these files to USB flash stick: dlink_dns-325-a1-initramfs-uImage dlink_dns-325-a1-squashfs-factory.bin dlink_dns-325-a1-squashfs-sysupgrade.bin u-boot.kwb (from u-boot-dns325 directory)
NAS setup
Connect LAN cable between router and NAS device
Connetc USB flash stick to NAS device
Connect serial to NAS device
Boot from new u-boot and install it
$ kwboot -p -b u-boot.kwb -B115200 -t /dev/ttyUSB0
Power on NAS
After download copleted and booted NAS device with new u-boot stop in bootloader by pressing any key
=> usb start
=> fatload usb 0 0x1000000 /u-boot.kwb
=> nand erase.part u-boot
=> nand write 0x1000000 u-boot ${filesize}
=> reset
Update MAC address in u-boot env
Stop in bootloader by pressing any key
Get your MAC address from label on chassis
=> setenv ethaddr XX:XX:XX:XX:XX:XX
=> saveenv
Install OpenWrt by flashing factory image from u-boot
=> usb start
=> fatload usb 0 0x1000000 /dlink_dns-325-a1-squashfs-factory.bin
=> nand erase.part ubi
=> nand write 0x1000000 ubi ${filesize}
=> reset
Based-on: #9296
Signed-off-by: Konstantin Meshkov <skyline@mail.ru>
[ refresh uboot patches ]
Link: https://github.com/openwrt/openwrt/pull/17924
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
MUSL doesn't provide PTHREAD_RWLOCK_PREFER_WRITER_NONRECURSIVE_NP as
it's only glibc and as the MACRO say, it's NP (not portable).
Add patch to check for this and disable overwriting the function
accordingly.
Fixes: 9bdf723476 ("libunistring: update to 1.4.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These patches fix the remaining issues with BCM5325 switches and allow
dropping the default VLAN on Huawei HG556a.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When transitioning from a config with one or more wifi-stations, to a configuration
that has no wifi-station; the file would not be empty/reset and the old wifi-station
entries would remain.
This is because iface_wpa_stations and iface_sae_stations return early if there
are no wifi-stations present, which is an incorrect behavior as it causes the
file to actually have old entries.
'sae_password_file' and 'wpa_psk_file' are also set by default inside
of iface_auth_type to same path as the one used by wifi-station, so it
is indeed going to be set in the config and would contain the old
entries.
This happens with reload and wifi restart. So the only solution
would be to manually remove the file.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20700
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device has one USB2.0 port, plus ethernet, 2x wifi, ethernet, xPON
and VoIP.
Installation instructions: (Assuming root shell via SSH or serial)
1. Place OpenWrt TRX file on a USB stick formatted VFAT
2. Plug in the stick to the modem
3. Type: mtd write -f -e tclinux /mnt/usb2_sda1/<name of file>.trx tclinux
At this point, both OpenWrt and the vendor OS will be installed
because the device has space for two operating systems. Switch the OS
to boot to OpenWrt:
1. mtd readflash tmpdata 999999999 0 reservearea
2. echo -n '0' | dd of=./tmpdata bs=1 count=1 seek=397311 conv=notrunc
3. mtd write -f -e reservearea ./tmpdata reservearea
4. reboot
WARNING: While you can install with SSH alone, you need serial to use
OpenWrt on EcoNet devices because the Ethernet driver has not yet been
developed.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The parameters must be aligned based on the last opened parenthesis
(+1). If this not a multiple of the tab size (8) then the rest
alignment must be done using spaces.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/20906
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
