This newly supported device has the same env partition size and
offset as SIMAX1800T.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19455
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SIM SIMAX1800U has the similar hardware design as the SIMAX1800T. The
only difference is the Ethernet portmap.
Specification
-------------
- SoC : Mediatek MT7621
- RAM : 256 MiB DDR3
- Flash : 128 MiB NAND Flash
- WLAN : Mediatek MT7905 DBDC
- 2.4 GHz : 2x2 MIMO WiFi6
- 5 GHz : 2x2 MIMO WiFi6
- Ethernet : MT7621 built-in 10/100/1000 Mbps 1x WAN; 3x LAN
- UART : 3.3V, 115200n8
- Buttons : 1x RESET; 1x WPS/MESH
- LEDs : 1x Multi-Color(Blue;Green;Red)
- Power : DC 12V1A
- CMIIT ID : 2022AP7163
- TFTP IP :
- server : 192.168.1.254
- router : 192.168.1.28
TFTP Installation(recommend)
------------
1. Set local tftp server IP "192.168.1.254" and NetMask "255.255.255.0".
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. tftpd64 is a good choice for Windows.
3. Remove all Ethernet cables and WiFi connections from the PC, except
for the one connected to the SIMAX1800U. Start the TFTP server, plug
in the power adapter and wait for the OpenWrt system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin". We need
it to back to the stock firmware.
5. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation
------------
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Return to Stock Firmware
----------------------------
Restore the backup firmware partition in the installation step 4.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | 98:xx:xx:xx:xx:b2 |
| LAN | 98:xx:xx:xx:xx:b5 |
| WAN | 98:xx:xx:xx:xx:b2 |
| WLAN2G | 98:xx:xx:xx:xx:b4 |
| WLAN5G | 9a:xx:xx:xx:xx:b4 |
+---------+-------------------+
Tips:
-----------
User can use `TFTP Installation` method to recover a brick device.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19455
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The workqueue items don't need to be processed directly when they are
scheduled. It can happen that they are simply processed at a much later
time. It is therefore necessary to ensure that all workqueue items of a
driver are no longer being processed before the driver (or structures of
this driver) are destroyed.
When skipping this step, the driver driver can cause a kernel Oops on
reboot.
Unfortunately, it is not recommended [1] to flush items out of the system
workqueue - simply because this can cause deadlocks. The driver itself must
have a private workqueue which is then flushed.
[1] https://lkml.kernel.org/r/49925af7-78a8-a3dd-bce6-cfc02e1a9236@I-love.SAKURA.ne.jp
Signed-off-by: Issam Hamdi <ih@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19570
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for building the ds2438 one-wire kernel module.
Signed-off-by: Andres Heinloo <andres@gfz.de>
Link: https://github.com/openwrt/openwrt/pull/19694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While this is discouraged to disable this option, both upstream and OpenWrt allows one to do it.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19611
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just like rtl930x, rtl931x also requires two reads to fetch current link
status.
While at it, rename the function to a proper naming scheme.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Co-developed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19578
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link status needs to be read twice, and a single register value is
enough for determining link status for all the ports
It is not necessary to go through each potential port separately and later
actually identify for which ports the interrupt actually was. The helper
for_each_set_bit() directly iterate through all set bits.
While at it, rename the function to a proper naming scheme.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19578
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently the SerDes driven SFP ports give strange ethtool readings
on RTL93xx devices. Especially duplex and speed are shown even if
no link is up and running. That leads to confusion because the MAC
reports arbitrary values.
Enhance the readout by refactoring the pcs_get_state() function.
Calculate speed/duplex/pause only if link is detected.
Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19575
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The media_sts register only shows type of link, fiber/copper,
and has nothing to do with the link status
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19575
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
84372dab89a8 hotplug: switch to using avl tree for hotplug subsystems
4d023b8a8c51 hotplug: send event notifications
467800980021 hotplug: ensure that the button subsystem is always registered
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sophos XG 210r3 is a rackmounted x86 based firewall with 6 RJ-45 gigabit
ethernet ports (eth0-5) and 2 SFP gigabit ethernet ports (eth6, eth7)
all running Intel NICs supported by igb driver. This board update maps
eth0 (left most RJ-45 port) as wan and eth1-7 as lan.
Signed-off-by: Steve Wavler <trenchcoatjedi@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19647
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-sfc should add support for Solarflare SFC9000 series based cards.
However after kernel 5.19, support for the 'Siena' subclass of
SFN5000/6000 devices has been separated out since they went EOL as they
are no longer being actively developed. As kmod-sfc no longer provides
driver support for these cards and hasn't since kernel 5.2, a new kernel
module is needed to support these 10Gb Ethernet cards. More info here:
https://cateee.net/lkddb/web-lkddb/SFC_SIENA.html and here:
https://www.phoronix.com/news/Solarflare-SFC-Siena-Linux-5.19
The module can be compiled in separately and works if kernel is custom
compiled;
OpenWRT has made these changes already with the SFC 'falcon' subclass of
drivers already. See 3c5d70a and e5ba6e9
This is building on excellent work by @ynezz and @nasbdh9
Signed-off-by: Steve Wavler <trenchcoatjedi@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19647
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We are slowly getting to the point where the mdio driver will be
carved out from the ethernet driver. Since the beginning it had
the feature to hand out SFP serdes as phys. So one can access
them from the phy driver. This will be kept during the final
migration and it even will provide a consistent interface for the
phy/serdes registers.
With this being done we need to identify how to handle the affected
ports in a generic way for all targets. Doing first things first,
this starts with a consistent DTS. Currently we have:
for RTL838x + Zyxel XGS1210:
phy-mode = "1000base-x"
managed = "in-band-status"
phy-handle = ...
for all other RTL93x devices:
phy-mode = "10gbase-r"
managed = "in-band-status"
pseudo-phy-handle = ...
Looking at the phylink kernel code one can see a nifty detail.
There is dynamic phy bringup depending on the mode.
int phylink_fwnode_phy_connect(struct phylink *pl,
const struct fwnode_handle *fwnode,
u32 flags)
{
struct fwnode_handle *phy_fwnode;
struct phy_device *phy_dev;
int ret;
/* Fixed links and 802.3z are handled without needing a PHY */
if (pl->cfg_link_an_mode == MLO_AN_FIXED ||
(pl->cfg_link_an_mode == MLO_AN_INBAND &&
phy_interface_mode_is_8023z(pl->link_interface)))
return 0;
...
}
Where 802.3z means 1000base-x or 2500base-x. Aligning this with
IEEE specs it means essentially:
- 10gbase-r defined ports with phy-handle must statically bring up
a phylink from the beginning that immediately depends on a
phy read_status() implementation.
- 1000base-x/2500base-x defined ports will dynamically bringup a
phylink during link detection regardless of a phy-handle. So
it usually runs at the moment when a SFP has been plugged in.
We currently still rely on a phy-handle but do not want to bring
up the phy immediately. Commit 4457c1eee4 ("realtek: rtl93xx:
support SFPs with phys") tried to fix exactly that error for
10gbase-r definied ports. Kernel shows "sfp sfp-p8: sfp_add_phy
failed: -EBUSY" in that case.
But it did it in the wrong way. It implemented a workaround by
introducing a DTS property "pseudo-phy-handle". Instead it
should have simply converted the DTS nodes to 1000base-x.
Revert the commit and fix the DTS with wrong definitions. From
now on we have a consistent SFP definition throughout all DTS
and targets.
Aside from the positive effect this setting has it is more or
less an arbitrary speed definition. When plugging in the SFP the
real speed will be choosen dynamically.
Fixes: 4457c1eee4 ("realtek: rtl93xx: support SFPs with phys")
Tested-By: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19648
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patches 12 and 13 have been superseded by patch 12. Other patches
have no significant changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19675
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling of both calibration and mac addresses is deprecated.
Also fixed calibration size for ath9k. AR9287 uses 3d8 for its size.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17289
Signed-off-by: Robert Marko <robimarko@gmail.com>
This will be used in the following commit to move MAC assignment of the
DSL interface to NVMEM.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17289
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds kernel module support for Microchip MCP342x family of I2C ADCs.
Tested on a custom board based on Hi-Link HLK-7628N.
Signed-off-by: Ondrej Kolar <ondrej@kolarovo.cz>
Link: https://github.com/openwrt/openwrt/pull/19619
Signed-off-by: Robert Marko <robimarko@gmail.com>
The current build recipe creates a lzma based initramfs and
a gzip based sysupgrade (installation) image. No need to
use different compression methods. Use lzma for both.
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19669
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add SoC revision, CPU part number, and a flag for engineering samples to
the rtl83xx_soc_info structure.
Also extend the system type string to include this information.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the definitions to mach-rtl83xx.h, so they can be used during init
to read more detailed SoC information. Also rename the RTL931X register,
as it has the same address on all RTL93xx.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read model name from the register instead of using hard-coded values.
Also remove detection of the unsupported Realtek ESW/SSW SoCs. The Fast
Ethernet variants of the Maple and Cypress series stay for now, but are
moved to the RTL8380/RTL8390 families.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Estimate the tx throughput based on the expected per-packet tx time.
This is useful for mesh implementations that rely on expected throughput,
e.g. 802.11s or batman-adv.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the lzma recipe for the device for both initramfs and sysupgrade to
save some flash space due to smaller image. U-Boot build on this device
has native lzma support.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19657
Signed-off-by: Robert Marko <robimarko@gmail.com>
The migration of the RTL930x mdio/serdes access functions over to the
mdio bus is a little more complicated than for RTL83xx. There are several
places where the serdes is accessed directly. So do it in two steps. With
this first step:
- use the rtmdio prefix for the serdes reader/writer functions
- move the functions over to the bus (inside the ethernet driver)
- Adapt all callers.
This is not only a copy/paste but the serdes access will be hardened too.
For this:
- put a mutex around the read/write functions because we have only
indirect register access through a mdio style bus.
- Verify input values to avoid data mess.
Tested-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19662
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RETSIGTYPE macro was historically used for signal handler return types,
defaulting to int on some legacy systems. This is no longer needed,
so we now use void as the return type.
Fixes a compiler error:
error: assignment to 'void (*)(int)' from incompatible pointer type 'int (*)()' [-Wincompatible-pointer-types]
Link: https://github.com/openwrt/openwrt/pull/19681
Signed-off-by: Nick Hainke <vincent@systemli.org>
Since 6.12 is now default, drop 6.6 support.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19682
Signed-off-by: Nick Hainke <vincent@systemli.org>
Let's switch the lantiq target to use kernel 6.12 by default.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19682
Signed-off-by: Nick Hainke <vincent@systemli.org>
Update default kernel version to 6.12 and drop configs and patches for
kernel 6.6.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/19666
Signed-off-by: Nick Hainke <vincent@systemli.org>
Like RTL839x the RTL930x SoCs have multithreading built in.
Activate it in the kernel configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19624
Signed-off-by: Robert Marko <robimarko@gmail.com>
Unless HE/EHT is enabled, the client should not process the RSN override IE.
This prevents picking up unsupported ciphers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow toggling autostart even for disabled devices
When switching from enabled to disabled, call teardown instead of setup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RTL839x mdio functions are scattered around the code. Relocate
them to the bus (still inside the ethernet driver).
Additionally provide a consistent SerDes register access through the
mdio bus. Until now when a SerDes directly drives a SFP module there
is no clear rule of how to handle its register set that consists of
two parts:
- c22 phy registers 0-15 live in the fiber page (2) of the SerDes
- other SerDes specific registers exist in pages before and after
The mdio bus and other SerDes functions are a wild mix of directly
looking into page 2 or just using self defined methods to access
data.
Adapt the bus to the new consistent phy interface that mixes the
SerDes register set like classic Realtek phys do it.
- Use register 31 as page select (already in the bus)
- Always keep the common registers 0-15 in place and read fiber page
- Map the SerDes internal registers into the upper vendor specific
registers 16-23 according to the page select register (31).
That gives a register mapping as follows:
+-----------------------+-----------------------+---------------+-------------+
| reg 0x00-0x0f | reg 0x10-0x17 | reg 0x18-0x1e | reg 0x1f |
+-----------------------+-----------------------+---------------+-------------+
| SerDes fiber page (3) | real SerDes registers | zero | SerDes page |
| registers 0 - 15 | in packages of 8 | | select reg |
+-----------------------+-----------------------+---------------+-------------+
Example to make it as clear as possible.
SerDes registers on a RTL839x show
Page / Reg | 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B ...
-------------+----------------------------------------------------------------
0 - SDS | 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248 0000 0F80 0000 ...
1 - SDS_EXT | 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA 8C64 00C3 1482 ...
2 - FIB | 1140 6189 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
3 - FIB_EXT | 1140 6109 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
This translates to this phy layout
| SerDes fiber registers normal SerDes registers zero p.sel
Page / Reg | 0x00 0x01 0x02 0x03 ... 0x10 0x11 0x12 0x13 ... 0x18 ... 0x1f
-------------+---------------------------------------------------------------
0 | 1140 6189 001C CA40 ... 0C03 0F00 7060 7106 ... 0000 ... 0000
1 | 1140 6189 001C CA40 ... 5248 0000 0F80 0000 ... 0000 ... 0001
...
4 | 1140 6189 001C CA40 ... 0000 0000 85FA 8C6D ... 0000 ... 0004
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19634
Signed-off-by: Robert Marko <robimarko@gmail.com>
GS1900-48 is missing from package/boot/uboot-tools/uboot-envtools/files/realtek, so add it to be consistent.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/19596
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Use SDS for phy 48/49
* Use correct link/phy settings for SFP ports
* Remove read-only flag from u-boot env so fw_setenv actually works
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/19596
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes a crash on some config reload types
Fixes: 816c2d86e7 ("hostapd: add support for MLO interfaces in ucode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
