hurricos/openwrt-mirror
1
0
Fork 0
mirror of git://git.openwrt.org/openwrt/openwrt.git synced 2025-12-06 04:34:00 -05:00
Code Issues Projects Releases Wiki Activity
da8428d277
openwrt-mirror/target/linux/ipq806x/image/Makefile
Lauro Moreno da8428d277 ipq806x: add support for Askey RT4230W REV6 
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)

At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.

Specifications:

    Qualcomm IPQ8065
    1 GB of RAM (DDR3)
    512 MB Flash (NAND)
    2x Wave 2 WiFi cards (QCA9984)
    5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
    1x LED (Controlled by a microcontroller that switches it between red and
        blue with different patterns)
    1x USB 3.0 Type-A
    12V DC Power Input
    UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
    Port settings are 115200n8

More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830
https://deviwiki.com/wiki/Askey_RAC2V1K

To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.

Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.

How to install:

Method 1: Install without opening the case using SSH and tftp

    You'll need:
    RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
    initramfs and sysupgrade images

    Connect to one of the router's LAN ports

    Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)

    After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
     fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
     fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
     fw_setenv bootdelay 8
     fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"

    Don't reboot the router yet.

    Install and set up a tftp server on your computer

    Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)

    Rename the initramfs image to initramfs.bin, and host it with the tftp
server

    Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
    After openwrt boots, ssh into it and run these commands:
    fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
 mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
    fw_setenv bootdelay 2

    After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.

Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)

    You'll need:
    initramfs and sysupgrade images
    Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case

    Install and set up a tftp server

    Set a static ip on the ethernet interface of your computer

    Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server

    Connect the wan port of the router to your computer

    Interrupt U-Boot and run these commands:
    setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
    setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
    setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"

    saveenv
    tftpboot initramfs.bin
    bootm

    After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.

Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00

425 lines
12 KiB
Makefile
Raw Blame History

# Copyright (c) 2014 The Linux Foundation. All rights reserved.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += TPLINK_BOARD_ID
define Build/buffalo-rootfs-cksum
( \
echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
$(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
) >> $@
endef
define Build/edimax-header
$(eval edimax_model=$(word 1,$(1)))
$(STAGING_DIR_HOST)/bin/mkedimaximg \
-b -s CSYS -m $(edimax_model) \
-f 0x70000 -S 0x1200000 \
-i $@ -o $@.new
@mv $@.new $@
endef
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_LOADADDR = 0x42208000
DEVICE_DTS = $$(SOC)-$(lastword $(subst _, ,$(1)))
DEVICE_DTS_CONFIG := config@1
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/LegacyImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
UBINIZE_OPTS := -E 5
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | append-metadata
endef
define Device/TpSafeImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
TPLINK_BOARD_ID :=
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata
endef
define Device/ZyXELImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$(KERNEL_SIZE)
KERNEL_NAME := zImage
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/askey_rt4230w-rev6
$(call Device/LegacyImage)
DEVICE_VENDOR := Askey
DEVICE_MODEL := RT4230W
DEVICE_VARIANT := REV6
SOC := qcom-ipq8065
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
KERNEL_IN_UBI := 1
endef
TARGET_DEVICES += askey_rt4230w-rev6
define Device/asrock_g10
$(call Device/FitImage)
$(call Device/UbiFit)
SOC := qcom-ipq8064
DEVICE_VENDOR := ASRock
DEVICE_MODEL := G10
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 5332k
DEVICE_PACKAGES := kmod-i2c-gpio ath10k-firmware-qca99x0-ct
IMAGE/nand-factory.bin := append-ubi | edimax-header RN67
endef
TARGET_DEVICES += asrock_g10
define Device/buffalo_wxr-2533dhp
$(call Device/LegacyImage)
SOC := qcom-ipq8064
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WXR-2533DHP
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += buffalo_wxr-2533dhp
define Device/compex_wpq864
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPQ864
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := qcom-ipq8064
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpq864
define Device/edgecore_ecw5410
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := ECW5410
SOC := qcom-ipq8068
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@v2.0-ap160
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-edgecore_ecw5410
endef
TARGET_DEVICES += edgecore_ecw5410
define Device/linksys_ea7500-v1
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA7500
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 3072k
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to $$$$(PAGESIZE)
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += linksys_ea7500-v1
define Device/linksys_ea8500
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8500
SOC := qcom-ipq8064
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 3072k
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
BOARD_NAME := ea8500
SUPPORTED_DEVICES += ea8500
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += linksys_ea8500
define Device/nec_wg2600hp
$(call Device/LegacyImage)
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG2600HP
SOC := qcom-ipq8064
BLOCKSIZE := 64k
BOARD_NAME := wg2600hp
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += nec_wg2600hp
define Device/nec_wg2600hp3
$(call Device/LegacyImage)
DEVICE_VENDOR := NEC Platforms
DEVICE_MODEL := Aterm WG2600HP3
SOC := qcom-ipq8062
BLOCKSIZE := 64k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform -kmod-usb-ohci -kmod-usb2 \
-kmod-usb-ledtrig-usbport -kmod-usb-phy-qcom-dwc3 -kmod-usb3 -kmod-usb-dwc3-qcom \
ath10k-firmware-qca9984-ct ipq-wifi-nec_wg2600hp3
endef
TARGET_DEVICES += nec_wg2600hp3
define Device/netgear_d7800
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 D7800
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := D7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := d7800
SUPPORTED_DEVICES += d7800
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += netgear_d7800
define Device/netgear_r7500
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 R7500
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7500
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500
SUPPORTED_DEVICES += r7500
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r7500
define Device/netgear_r7500v2
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 R7500
DEVICE_VARIANT := v2
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7500v2
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500v2
SUPPORTED_DEVICES += r7500v2
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r7500v2
define Device/netgear_r7800
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4S R7800
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7800
SUPPORTED_DEVICES += r7800
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += netgear_r7800
define Device/qcom_ipq8064-ap148
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP148
DEVICE_VARIANT := standard
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap148
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES += ap148
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap148
define Device/qcom_ipq8064-ap148-legacy
$(call Device/LegacyImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP148
DEVICE_VARIANT := legacy
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap148
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
define Device/qcom_ipq8064-ap161
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP161
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap161
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap161
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap161
define Device/qcom_ipq8064-db149
$(call Device/FitImage)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := DB149
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-db149
KERNEL_INSTALL := 1
BOARD_NAME := db149
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-db149
define Device/tplink_ad7200
$(call Device/TpSafeImage)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := AD7200
DEVICE_VARIANT := v1/v2
DEVICE_ALT0_VENDOR := TP-Link
DEVICE_ALT0_MODEL := Talon AD7200
DEVICE_ALT0_VARIANT := v1/v2
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
TPLINK_BOARD_ID := AD7200
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-wil6210
endef
TARGET_DEVICES += tplink_ad7200
define Device/tplink_c2600
$(call Device/TpSafeImage)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer C2600
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := c2600
SUPPORTED_DEVICES += c2600
TPLINK_BOARD_ID := C2600
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += tplink_c2600
define Device/tplink_vr2600v
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer VR2600v
DEVICE_VARIANT := v1
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SIZE := 3072k
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := vr2600v
SUPPORTED_DEVICES += vr2600v
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += tplink_vr2600v
define Device/ubnt_unifi-ac-hd
$(call Device/FitImageLzma)
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi AC HD
SOC := qcom-ipq8064
BLOCKSIZE := 64k
IMAGE_SIZE := 14784k
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata | check-size
endef
TARGET_DEVICES += ubnt_unifi-ac-hd
define Device/zyxel_nbg6817
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6817
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
BLOCKSIZE := 64k
BOARD_NAME := nbg6817
RAS_BOARD := NBG6817
RAS_ROOTFS_SIZE := 20934k
RAS_VERSION := "V1.99(OWRT.9999)C0"
SUPPORTED_DEVICES += nbg6817
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
$(call Device/ZyXELImage)
endef
TARGET_DEVICES += zyxel_nbg6817
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink