mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-11-02 05:54:26 -05:00
1c2f7b5115
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN: 1x Reset
1x WPS
1x USB eject
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
Dupont 4 pin header
Rear RJ45 serial port non-functional
USB: 1x v2.0
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
84 lines
1.4 KiB
Plaintext
84 lines
1.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca9558_devolo_dvl1xxx.dtsi"
|
|
|
|
/ {
|
|
compatible = "devolo,dvl1750e", "qca,qca9557";
|
|
model = "devolo WiFi pro 1750e";
|
|
|
|
aliases {
|
|
led-boot = &status_blue;
|
|
led-failsafe = &status_red;
|
|
led-running = &status_blue;
|
|
led-upgrade = &status_red;
|
|
};
|
|
|
|
keys {
|
|
wps {
|
|
label = "WPS Button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
usb_eject {
|
|
label = "USB Eject Button";
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status_blue: status_blue {
|
|
label = "dvl1750e:blue:status";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
status_red: status_red {
|
|
label = "dvl1750e:red:status";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
beeper {
|
|
compatible = "gpio-beeper";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
|
|
gpio_usb_power {
|
|
gpio-export,name = "devolo:power:usb";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
};
|