mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-11-01 06:24:27 -04:00
b4184c666c
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
|---|---|---|
| .. | ||
| qcom-ipq4018-a42.dts | ||
| qcom-ipq4018-ap120c-ac.dts | ||
| qcom-ipq4018-cap-ac.dts | ||
| qcom-ipq4018-cs-w3-wd1200g-eup.dts | ||
| qcom-ipq4018-dap-2610.dts | ||
| qcom-ipq4018-ea6350v3.dts | ||
| qcom-ipq4018-eap1300.dts | ||
| qcom-ipq4018-ecw5211.dts | ||
| qcom-ipq4018-emd1.dts | ||
| qcom-ipq4018-emr3500.dts | ||
| qcom-ipq4018-ens620ext.dts | ||
| qcom-ipq4018-ex61x0v2.dtsi | ||
| qcom-ipq4018-ex6100v2.dts | ||
| qcom-ipq4018-ex6150v2.dts | ||
| qcom-ipq4018-fritzbox-4040.dts | ||
| qcom-ipq4018-gl-ap1300.dts | ||
| qcom-ipq4018-hap-ac2.dts | ||
| qcom-ipq4018-jalapeno.dts | ||
| qcom-ipq4018-jalapeno.dtsi | ||
| qcom-ipq4018-magic-2-wifi-next.dts | ||
| qcom-ipq4018-meshpoint-one.dts | ||
| qcom-ipq4018-nbg6617.dts | ||
| qcom-ipq4018-pa1200.dts | ||
| qcom-ipq4018-rt-ac58u.dts | ||
| qcom-ipq4018-rutx10.dts | ||
| qcom-ipq4018-rutx.dtsi | ||
| qcom-ipq4018-sxtsq-5-ac.dts | ||
| qcom-ipq4018-wac510.dts | ||
| qcom-ipq4018-whw01-v1.dts | ||
| qcom-ipq4018-wre6606.dts | ||
| qcom-ipq4018-wrtq-329acn.dts | ||
| qcom-ipq4019-a62.dts | ||
| qcom-ipq4019-cm520-79f.dts | ||
| qcom-ipq4019-e2600ac-c1.dts | ||
| qcom-ipq4019-e2600ac-c2.dts | ||
| qcom-ipq4019-e2600ac.dtsi | ||
| qcom-ipq4019-ea8300.dts | ||
| qcom-ipq4019-eap2200.dts | ||
| qcom-ipq4019-fritzbox-7530.dts | ||
| qcom-ipq4019-fritzrepeater-1200.dts | ||
| qcom-ipq4019-fritzrepeater-3000.dts | ||
| qcom-ipq4019-gl-b2200.dts | ||
| qcom-ipq4019-habanero-dvk.dts | ||
| qcom-ipq4019-hap-ac3.dts | ||
| qcom-ipq4019-lhgg-60ad.dts | ||
| qcom-ipq4019-map-ac2200.dts | ||
| qcom-ipq4019-mf286d.dts | ||
| qcom-ipq4019-mr8300.dts | ||
| qcom-ipq4019-oap100.dts | ||
| qcom-ipq4019-orbi.dtsi | ||
| qcom-ipq4019-pa2200.dts | ||
| qcom-ipq4019-r619ac-64m.dts | ||
| qcom-ipq4019-r619ac-128m.dts | ||
| qcom-ipq4019-r619ac.dtsi | ||
| qcom-ipq4019-rbr50.dts | ||
| qcom-ipq4019-rbs50.dts | ||
| qcom-ipq4019-rt-ac42u.dts | ||
| qcom-ipq4019-rtl30vw.dts | ||
| qcom-ipq4019-srr60.dts | ||
| qcom-ipq4019-srs60.dts | ||
| qcom-ipq4019-u4019-32m.dts | ||
| qcom-ipq4019-u4019.dtsi | ||
| qcom-ipq4019-wifi.dts | ||
| qcom-ipq4019-wpj419.dts | ||
| qcom-ipq4019-wtr-m2133hp.dts | ||
| qcom-ipq4019-x1pro.dts | ||
| qcom-ipq4019-x1pro.dtsi | ||
| qcom-ipq4019-xx8300.dtsi | ||
| qcom-ipq4028-wpj428.dts | ||
| qcom-ipq4029-ap-303.dts | ||
| qcom-ipq4029-ap-303h.dts | ||
| qcom-ipq4029-ap-365.dts | ||
| qcom-ipq4029-aruba-glenmorangie.dtsi | ||
| qcom-ipq4029-gl-b1300.dts | ||
| qcom-ipq4029-gl-s1300.dts | ||
| qcom-ipq4029-mr33.dts | ||