hurricos/openwrt-mirror
1
0
Fork 0
mirror of git://git.openwrt.org/openwrt/openwrt.git synced 2025-12-08 05:32:09 -05:00
Code Issues Projects Releases Wiki Activity
a30abb1b6b
openwrt-mirror/target/linux/ipq40xx/image/Makefile
DENG Qingfang a30abb1b6b ipq40xx: add support for MobiPromo CM520-79F 
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019

Specification:

SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
      2 (USB, CAN) are GPIO
      other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset

Flash instruction:
Disassemble the router, connect UART pins like this:
 GND TX    RX
  [x x . . x .]
  [. . . . . .]

(QCA8075 and IPQ4019 below)
Baud-rate: 115200

Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
	printenv
	(Copy the output to somewhere save)
Set bootenv:
	setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
	setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
	setenv cm520_boot 'run set_ubi; run bootkernel'
	setenv bootcmd 'run cm520_boot'
	setenv bootargs
	saveenv
Boot initramfs from TFTP:
	tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
	bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
	cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP

Upload nand-factory.ubi to /tmp via SCP, then run
	mtd erase rootfs
	mtd write /tmp/*nand-factory.ubi rootfs
	reboot

To revert to stock image, restore default bootenv in uboot UART console
	setenv bootcmd 'bootipq'
	printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
	saveenv
upload the backed up mtd12.bin and run
	tftpboot mtd12.bin
	nand erase 0xb80000 0x7480000
	nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
	cd /tmp
	cat /dev/mtd7 > mtd7.bin
	echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
	for i in 28 48 68 108; do
		dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
	done
	mtd write mtd7.bin BOOTCONFIG
	mtd write mtd7.bin BOOTCONFIG1

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:22:26 +02:00

633 lines
19 KiB
Makefile
Raw Blame History

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR := 0x80208000
DEVICE_DTS = $$(SOC)-$(lastword $(subst _, ,$(1)))
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitzImage
KERNEL_SUFFIX := -fit-zImage.itb
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := zImage
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.bin
IMAGE/nand-factory.ubi := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
IMAGES := factory.img sysupgrade.bin
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
endef
define Build/mkmylofw_32m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad'; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
$@.new
@mv $@.new $@
endef
define Build/SenaoFW
-$(STAGING_DIR_HOST)/bin/mksenaofw \
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
-e $@ \
-o $@.new
@cp $@.new $@
endef
define Build/wrgg-image
mkwrggimg -i $@ \
-o $@.new \
-d "$(WRGG_DEVNAME)" \
-s "$(WRGG_SIGNATURE)" \
-v "" -m "" -B ""
mv $@.new $@
endef
define Device/8dev_habanero-dvk
$(call Device/FitImageLzma)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Habanero DVK
IMAGE_SIZE := 30976k
SOC := qcom-ipq4019
DEVICE_PACKAGES := ipq-wifi-8dev_habanero-dvk
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | append-metadata | check-size
endef
TARGET_DEVICES += 8dev_habanero-dvk
define Device/8dev_jalapeno-common
$(call Device/FitImage)
$(call Device/UbiFit)
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := qcom-ipq4018
endef
define Device/8dev_jalapeno
$(call Device/8dev_jalapeno-common)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Jalapeno
endef
TARGET_DEVICES += 8dev_jalapeno
define Device/alfa-network_ap120c-ac
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP120C-AC
SOC := qcom-ipq4018
DEVICE_PACKAGES := kmod-usb-acm \
kmod-tpm-i2c-atmel uboot-envtools
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += alfa-network_ap120c-ac
define Device/aruba_ap-303
$(call Device/FitImageLzma)
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-303
SOC := qcom-ipq4029
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += aruba_ap-303
define Device/aruba_ap-303h
$(call Device/FitImageLzma)
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-303H
SOC := qcom-ipq4029
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += aruba_ap-303h
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := Lyra (MAP-AC2200)
SOC := qcom-ipq4019
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
endef
TARGET_DEVICES += asus_map-ac2200
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC58U
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
# Since u-boot works with strings we either need another fixup step
# to add a version... or we are very careful not to add '\0' into that
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac58u
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 4040
SOC := qcom-ipq4018
BOARD_NAME := fritz4040
IMAGE_SIZE := 29056k
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
UBOOT_PARTITION_SIZE := 524288
IMAGES = eva.bin sysupgrade.bin
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := fritz-tffs fritz-caldata
endef
TARGET_DEVICES += avm_fritzbox-4040
define Device/avm_fritzbox-7530
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 7530
SOC := qcom-ipq4019
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += avm_fritzbox-7530
define Device/avm_fritzrepeater-1200
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 1200
SOC := qcom-ipq4019
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += avm_fritzrepeater-1200
define Device/avm_fritzrepeater-3000
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 3000
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += avm_fritzrepeater-3000
define Device/cilab_meshpoint-one
$(call Device/8dev_jalapeno-common)
DEVICE_VENDOR := Crisis Innovation Lab
DEVICE_MODEL := MeshPoint.One
DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
endef
TARGET_DEVICES += cilab_meshpoint-one
define Device/compex_wpj419
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ419
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@12
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
endef
TARGET_DEVICES += compex_wpj419
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ428
SOC := qcom-ipq4028
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
IMAGE_SIZE := 31232k
KERNEL_SIZE := 4096k
IMAGES = sysupgrade.bin cpximg-6a04.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpj428
define Device/dlink_dap-2610
$(call Device/FitImageLzma)
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2610
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
BLOCKSIZE := 64k
WRGG_DEVNAME := /dev/mtdblock/8
WRGG_SIGNATURE := wapac30_dkbs_dap2610
IMAGE_SIZE := 14080k
IMAGES := sysupgrade.bin factory.bin
# Bootloader expects a special 160 byte header which is added by
# wrgg-image.
# Factory image size must be larger than 6MB, and size in wrgg header must
# match actual factory image size to be flashable from D-Link http server.
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
# cannot be part of the wrgg image. This is solved in the factory image by
# having the rootfs at the end of the image (without pad-rootfs). And in
# the sysupgrade image only the kernel is included in the wrgg checksum,
# but this is not flashable from the D-link http server.
# append-rootfs must start on an erase block boundary.
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := ipq-wifi-dlink_dap2610
endef
TARGET_DEVICES += dlink_dap-2610
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP1300
DEVICE_DTS_CONFIG := config@4
BOARD_NAME := eap1300
SOC := qcom-ipq4018
KERNEL_SIZE := 5120k
IMAGE_SIZE := 25344k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += engenius_eap1300
define Device/engenius_eap2200
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP2200
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
endef
TARGET_DEVICES += engenius_eap2200
define Device/engenius_emd1
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EMD1
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGE_SIZE := 30720k
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
endef
TARGET_DEVICES += engenius_emd1
define Device/engenius_ens620ext
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ENS620EXT
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
PAGESIZE := 256
BOARD_NAME := ENS620EXT
VENDOR_ID := 0x0101
PRODUCT_ID := 0x79
PRODUCT_ID_NEW := 0xA4
DATECODE := 190507
FW_VER := 3.1.2
FW_VER_NEW := 3.5.6
CW_VER := 1.8.99
IMAGE_SIZE := 21312k
KERNEL_SIZE := 5120k
FILESYSTEMS := squashfs
IMAGES := sysupgrade.bin factory_30.bin factory_35.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
endef
TARGET_DEVICES += engenius_ens620ext
define Device/ezviz_cs-w3-wd1200g-eup
$(call Device/FitImage)
DEVICE_VENDOR := EZVIZ
DEVICE_MODEL := CS-W3-WD1200G
DEVICE_VARIANT := EUP
DEVICE_DTS_CONFIG := config@4
IMAGE_SIZE := 14848k
SOC := qcom-ipq4018
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
ipq-wifi-ezviz_cs-w3-wd1200g-eup
endef
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-B1300
BOARD_NAME := gl-b1300
SOC := qcom-ipq4029
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += glinet_gl-b1300
define Device/linksys_ea6350v3
# The Linksys EA6350v3 has a uboot bootloader that does not
# support either booting lzma kernel images nor booting UBI
# partitions. This uboot, however, supports raw kernel images and
# gzipped images.
#
# As for the time of writing this, the device will boot the kernel
# from a fixed address with a fixed length of 3MiB. Also, the
# device has a hard-coded kernel command line that requieres the
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
# Oh... and the kernel partition overlaps with the rootfs
# partition (the same for alt_kernel and alt_rootfs).
#
# If you are planing re-partitioning the device, you may want to
# keep those details in mind:
# 1. The kernel adresses you should honor are 0x00000000 and
# 0x02800000 respectively.
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
# 4. The kernel command line from uboot is harcoded to boot with
# rootfs either in mtd11 or mtd13.
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6350
DEVICE_VARIANT := v3
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 3072k
IMAGE_SIZE := 37888k
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += linksys_ea6350v3
define Device/linksys_ea8300
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8300
SOC := qcom-ipq4019
KERNEL_SIZE := 3072k
IMAGE_SIZE := 87040k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES := sysupgrade.bin factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_ea8300
define Device/meraki_mr33
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR33
SOC := qcom-ipq4029
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES = sysupgrade.bin
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
endef
TARGET_DEVICES += meraki_mr33
define Device/mobipromo_cm520-79f
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := MobiPromo
DEVICE_MODEL := CM520-79F
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += mobipromo_cm520-79f
define Device/netgear_ex61x0v2
$(call Device/DniImage)
DEVICE_DTS_CONFIG := config@4
NETGEAR_BOARD_ID := EX6150v2series
NETGEAR_HW_ID := 29765285+16+0+128+2x2
SOC := qcom-ipq4018
endef
define Device/netgear_ex6100v2
$(call Device/netgear_ex61x0v2)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := EX6100
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += netgear_ex6100v2
define Device/netgear_ex6150v2
$(call Device/netgear_ex61x0v2)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := EX6150
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += netgear_ex6150v2
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A42
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@om.a42
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += openmesh_a42
define Device/openmesh_a62
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A62
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@om.a62
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
endef
TARGET_DEVICES += openmesh_a62
define Device/qcom_ap-dk01.1-c1
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK01.1
DEVICE_VARIANT := C1
BOARD_NAME := ap-dk01.1-c1
SOC := qcom-ipq4019
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK04.1
DEVICE_VARIANT := C1
SOC := qcom-ipq4019
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
define Device/qxwlan_e2600ac-c1
$(call Device/FitImage)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C1
BOARD_NAME := e2600ac-c1
SOC := qcom-ipq4019
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
endef
TARGET_DEVICES += qxwlan_e2600ac-c1
define Device/qxwlan_e2600ac-c2
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C2
SOC := qcom-ipq4019
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
endef
TARGET_DEVICES += qxwlan_e2600ac-c2
define Device/unielec_u4019-32m
$(call Device/FitImage)
DEVICE_VENDOR := Unielec
DEVICE_MODEL := U4019
DEVICE_VARIANT := 32M
BOARD_NAME := u4019-32m
SOC := qcom-ipq4019
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += unielec_u4019-32m
define Device/zyxel_nbg6617
$(call Device/FitImageLzma)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6617
SOC := qcom-ipq4018
ROOTFS_SIZE := 24960k
RAS_BOARD := NBG6617
RAS_ROOTFS_SIZE := 19840k
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGES := sysupgrade.bin factory.bin
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
# at least as large as the one of the initial firmware image (not the current
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
# this minimum-size. However, the larger image can be flashed both ways.
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zyxel_nbg6617
define Device/zyxel_wre6606
$(call Device/FitImage)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := WRE6606
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
endef
TARGET_DEVICES += zyxel_wre6606
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink