hurricos/openwrt-mirror
1
0
Fork 0
mirror of git://git.openwrt.org/openwrt/openwrt.git synced 2025-12-14 16:42:10 -05:00
Code Issues Projects Releases Wiki Activity
80baffd2aa
openwrt-mirror/target/linux/ipq40xx/files/arch/arm/boot/dts
History
Tomasz Maciej Nowak 80baffd2aa ipq40xx: add support for Pakedge WR-1 
Pakedge WR-1 is a dual-band wireless router.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
      1. 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Rename initramfs image to:
   openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
   and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
   reset button. Hold the button, on the lates bootloader version, when
   Power and WiFi-5 LEDs will start blinking release it. For the older
   bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
   minute) the Power LED will start blinking, when stops, router is fully
   booted.
4. Connect to one of LAN ports and use SSH to open the shell at
   192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
   at some point, You want to go back to original firmware. The firmware
   provided by manufacturer on its site is encrypted and U-Boot accepts
   only decrypted factory images, so there's no way to restore original
   firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
   and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
   LED will start blinking, wait till it stops, then router is ready for
   configuration.

Additional information
U-Boot command line is password protected. Password is unknown.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-07 21:21:38 +02:00
..
qcom-ipq4018-a42.dts ipq40xx: DTS style updates for OpenMesh devices 2020-11-23 13:44:47 +01:00
qcom-ipq4018-ap120c-ac.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-cap-ac.dts ipq40xx: mikrotik: make RouterBoot partition writeable 2022-06-29 12:34:49 +02:00
qcom-ipq4018-cs-w3-wd1200g-eup.dts ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUP 2021-12-04 00:36:47 +01:00
qcom-ipq4018-dap-2610.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4018-ea6350v3.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-eap1300.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-ecw5211.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-emd1.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4018-emr3500.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4018-ens620ext.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4018-ex61x0v2.dtsi ipq40xx: utilize nvmem on Netgear EX61X0 v2 Series 2021-11-28 01:13:08 +01:00
qcom-ipq4018-ex6100v2.dts ipq40xx: tidy up dts-v1 statements 2020-09-25 21:10:41 +02:00
qcom-ipq4018-ex6150v2.dts ipq40xx: tidy up dts-v1 statements 2020-09-25 21:10:41 +02:00
qcom-ipq4018-fritzbox-4040.dts ipq40xx: dts: convert PHY GPIO bindings 2020-12-23 16:36:08 +01:00
qcom-ipq4018-gl-ap1300.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-hap-ac2.dts ipq40xx: mikrotik: make RouterBoot partition writeable 2022-06-29 12:34:49 +02:00
qcom-ipq4018-jalapeno.dts ipq40xx: consolidate DTS files 2020-06-23 21:02:26 +02:00
qcom-ipq4018-jalapeno.dtsi ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-magic-2-wifi-next.dts ipq40xx: add support for devolo Magic 2 WiFi next 2020-12-22 20:55:40 +01:00
qcom-ipq4018-meshpoint-one.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4018-nbg6617.dts ipq40xx: increase SPI frequency for Zyxel NBG6617 2021-07-11 01:38:52 +02:00
qcom-ipq4018-pa1200.dts ipq40xx: add support for Plasma Cloud PA1200 2020-12-22 19:11:50 +01:00
qcom-ipq4018-rt-ac58u.dts ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U 2022-01-15 17:21:01 +01:00
qcom-ipq4018-rutx10.dts ipq40xx: Add support for Teltonika RUTX10 2021-11-28 18:39:01 +01:00
qcom-ipq4018-rutx.dtsi ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4018-sxtsq-5-ac.dts ipq40xx: mikrotik: make RouterBoot partition writeable 2022-06-29 12:34:49 +02:00
qcom-ipq4018-wac510.dts ipq40xx: WAC510: device-tree overhauling 2022-03-26 02:02:44 +01:00
qcom-ipq4018-wap-ac.dts ipq40xx: add MikroTik wAP ac (RBwAPG-5HacD2HnD) support 2022-07-18 01:45:47 +02:00
qcom-ipq4018-whw01-v1.dts ipq40xx: add support for Linksys WHW01 v1 2022-06-05 21:19:32 +02:00
qcom-ipq4018-wr-1.dts ipq40xx: add support for Pakedge WR-1 2022-09-07 21:21:38 +02:00
qcom-ipq4018-wre6606.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4018-wrtq-329acn.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-a62.dts ipq40xx: DTS style updates for OpenMesh devices 2020-11-23 13:44:47 +01:00
qcom-ipq4019-cm520-79f.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-e2600ac-c1.dts ipq40xx: update E2600AC c1/c2 board 2022-03-25 18:14:13 +01:00
qcom-ipq4019-e2600ac-c2.dts ipq40xx: update E2600AC c1/c2 board 2022-03-25 18:14:13 +01:00
qcom-ipq4019-e2600ac.dtsi ipq40xx: update E2600AC c1/c2 board 2022-03-25 18:14:13 +01:00
qcom-ipq4019-ea8300.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4019-eap2200.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-fritzbox-7530.dts IPQ4019: AVM FRITZ!Box 7530: Remove NAND ECC restrictions from DTS 2022-05-15 16:35:00 +02:00
qcom-ipq4019-fritzrepeater-1200.dts ipq40xx: fix FRITZRepeater 1200 RGMII delay 2021-07-17 20:06:49 +02:00
qcom-ipq4019-fritzrepeater-3000.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4019-gl-b2200.dts ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200 2022-02-19 18:29:42 +01:00
qcom-ipq4019-habanero-dvk.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-hap-ac3.dts ipq40xx: mikrotik: make RouterBoot partition writeable 2022-06-29 12:34:49 +02:00
qcom-ipq4019-lhgg-60ad.dts ipq40xx: mikrotik: make RouterBoot partition writeable 2022-06-29 12:34:49 +02:00
qcom-ipq4019-map-ac2200.dts ipq40xx: Lyra: update RGB LED-Controller node for 5.10+ 2022-05-14 11:08:45 +02:00
qcom-ipq4019-mf286d.dts ipq40xx: add support for ZTE MF286D 2022-02-05 00:44:35 +01:00
qcom-ipq4019-mr8300.dts ipq40xx: remove model name from LED labels 2020-10-07 01:31:37 +02:00
qcom-ipq4019-oap100.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-orbi.dtsi ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50 2021-11-01 00:56:51 +01:00
qcom-ipq4019-pa2200.dts ipq40xx: add support for Plasma Cloud PA2200 2020-12-22 19:11:50 +01:00
qcom-ipq4019-r619ac-64m.dts ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0) 2021-11-14 14:28:34 +01:00
qcom-ipq4019-r619ac-128m.dts ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0) 2021-11-14 14:28:34 +01:00
qcom-ipq4019-r619ac.dtsi ipq40xx: R619AC: replace space with - separator in variant string 2022-07-15 15:21:44 +02:00
qcom-ipq4019-rbr50.dts ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50 2021-11-01 00:56:51 +01:00
qcom-ipq4019-rbs50.dts ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50 2021-11-01 00:56:51 +01:00
qcom-ipq4019-rt-ac42u.dts ipq40xx: rename RT-AC42U WLAN/LAN LEDs 2022-01-17 20:38:43 +09:00
qcom-ipq4019-rtl30vw.dts ipq40xx: revert Cell-C RTL30VW to legacy caldata extraction 2022-05-15 16:32:25 +02:00
qcom-ipq4019-srr60.dts ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50 2021-11-01 00:56:51 +01:00
qcom-ipq4019-srs60.dts ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50 2021-11-01 00:56:51 +01:00
qcom-ipq4019-u4019-32m.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-u4019.dtsi ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-wifi.dts ipq40xx: Add subtarget for Google WiFi (Gale) 2022-03-25 18:14:13 +01:00
qcom-ipq4019-wpj419.dts ipq40xx: fix wrong nand definition for wpj419 2022-05-01 13:40:13 +09:00
qcom-ipq4019-wtr-m2133hp.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4019-x1pro.dts ipq40xx: add support for Telco X1 Pro 2022-03-19 20:05:00 +01:00
qcom-ipq4019-x1pro.dtsi ipq40xx: add support for Telco X1 Pro 2022-03-19 20:05:00 +01:00
qcom-ipq4019-xx8300.dtsi ipq40xx: tidy up dts-v1 statements 2020-09-25 21:10:41 +02:00
qcom-ipq4028-wpj428.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4029-ap-303.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4029-ap-303h.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4029-ap-365.dts ipq40xx: add Aruba AP-365 specific BDF 2022-06-02 16:50:12 +02:00
qcom-ipq4029-aruba-glenmorangie.dtsi ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4029-gl-b1300.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4029-gl-s1300.dts ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data 2022-01-15 17:26:55 +01:00
qcom-ipq4029-insect-common.dtsi ipq40xx: add support for Meraki MR74 2022-06-19 12:31:02 +02:00
qcom-ipq4029-mr33.dts ipq40xx: add support for Meraki MR74 2022-06-19 12:31:02 +02:00
qcom-ipq4029-mr74.dts ipq40xx: add support for Meraki MR74 2022-06-19 12:31:02 +02:00
qcom-ipq4029-ws-ap3915i.dts ipq40xx: add support for Extreme Networks WS-AP3915i 2022-09-06 02:55:05 +02:00