openwrt-mirror/package/firmware
Yang Xiwen 5dbf93c8c5 ipq60xx: add support for TP-Link EAP623-Outdoor HD v1
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
  Active High) and an LED global control GPIO (GPIO 36 Active High, set
  up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)

Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
   the pad near T31 respectively. Be sure not to connect VCC and
   crossover TX and RX.
3. Copy RAM firmware image
   openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
   to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
   serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
   # setenv serverip 192.168.0.1
   # setenv ipaddr 192.168.0.99
   # tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
   # bootm
   You may need to type Ctrl+C and Enter before running these commands
   to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
   to be installed (check IP address):
   $ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
   # cd /tmp
   # sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.

Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-04-09 09:50:31 +02:00
..
ath10k-ct-firmware ath10k-ct-firmware: remove QCA9888 board file symbolic link 2025-03-31 14:16:53 +02:00
ath11k-firmware ath11k-firmware: add wifi firmware for QCN6122 2025-02-06 09:51:13 +01:00
broadcom-sprom treewide: update PKG_MIRROR_HASH to zst 2024-04-06 11:24:18 +02:00
cypress-firmware cypress-firmware: fix version for APK 2024-10-29 00:07:51 +01:00
cypress-nvram cypress-nvram: consolidate NVRAM packages 2022-11-16 20:14:13 +01:00
intel-microcode firmware: intel-microcode: update to 20250211 2025-03-15 10:09:29 +01:00
ipq-wifi ipq60xx: add support for TP-Link EAP623-Outdoor HD v1 2025-04-09 09:50:31 +02:00
ixp4xx-microcode firmware: Resurrect the ixp4xx microcode package 2023-10-25 11:28:15 +02:00
lantiq lantiq-gphy-firmware: add package 2025-03-15 13:52:40 +01:00
layerscape ls-mc: bump to 10.39.0 2024-09-22 16:21:02 +02:00
linux-firmware linux-firmware: Add support for Intel ICE 2025-03-17 14:53:53 +01:00
murata-firmware murata-firmware: add new package 2024-11-23 15:53:21 +01:00
murata-nvram murata-nvram: add new package 2024-11-23 15:53:21 +01:00
omnia-mcu-firmware packages: drop DEVICE specific dependency for omnia 2024-11-05 09:59:49 +01:00
prism54-firmware prism54-firmware: set DL_DIR to package specific subdirectory 2022-09-22 16:48:37 -04:00
wireless-regdb wireless-regdb: Update to version 2025.02.20 2025-02-24 00:30:21 +01:00