mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-12-06 04:34:00 -05:00
2090b8af0a
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org