hurricos/openwrt-mirror
1
0
Fork 0
mirror of git://git.openwrt.org/openwrt/openwrt.git synced 2025-12-23 04:52:10 -05:00
Code Issues Projects Releases Wiki Activity
64,610 Commits 12 Branches 87 Tags 255 MiB
dd57c070e9
Commit Graph

6 Commits

Author SHA1 Message Date
Alexandru Gagniuc
51c1ea08d0 qualcommax: ipq60xx: add TP-Link EAP625-Outdoor HD v1 support 
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.

Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.

This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.

Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
  * Gigabit RJ45 port with PoE input
* WLAN:
  * 2.4GHz/5GHz
* LEDs:
  * Multi-color System LED (Green/Amber)
* Buttons:
  * 1x Reset
* UART: 4-pin unpopulated header
  * 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V

Installation:
=============

Web UI method
-------------

Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:

ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>

Disable signature verification:

cliclientd stopcs

Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
 * Go to System -> Firmware Update.
 * Under "New Firmware File", click "Browse" and select the image
 * Select "Update" and confirm by clicking "OK".

If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.

NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.

TFTP method
-----------

To flash via tftp, first place the initramfs image on the TFTP server.

setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm

This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
 2025-05-14 19:38:25 +02:00
Yang Xiwen
5dbf93c8c5 ipq60xx: add support for TP-Link EAP623-Outdoor HD v1 
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
  Active High) and an LED global control GPIO (GPIO 36 Active High, set
  up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)

Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
   the pad near T31 respectively. Be sure not to connect VCC and
   crossover TX and RX.
3. Copy RAM firmware image
   openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
   to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
   serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
   # setenv serverip 192.168.0.1
   # setenv ipaddr 192.168.0.99
   # tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
   # bootm
   You may need to type Ctrl+C and Enter before running these commands
   to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
   to be installed (check IP address):
   $ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
   # cd /tmp
   # sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.

Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
 2025-04-09 09:50:31 +02:00
Erik Servili
a0c1c9df97 qualcommax: ipq60xx: add support for Netgear WAX610 and WAX610Y 
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.

Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
  * 2.5GbE RJ45 port with PoE input
* WLAN:
  * 2.4GHz/5GHz
* LEDs:
  * Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
  * Ethernet: Dual-color LED (Green / Orange)
  * 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
  * 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
  * 1x Reset
* UART: 4-pin populated header
  * Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX

Installation:
=============

Web UI method
-------------

Set up the device using the stock web UI in local management mode.

Download the ui-factory.tar image.
 * Enter the Management tab
 * Select Maintenance->Upgrade->Firmware Upgrade
 * Ensure the "Upgrade Options" field has "Local" selected
 * Click "Browse File" and select the image
 * Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page

The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.

TFTP method
-----------

To flash via tftp, first place the initramfs image on the TFTP server.

    setenv serverip <ip of tftp server>
    setenv ipaddr <ip in same subnet as tftp server>
    tftpboot netgear_wax610-initramfs-uImage.itb
    bootm

This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.

Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
 2025-04-04 14:38:01 +02:00
Weikai Kong
a1bf306bb7 qualcommax: ipq60xx: add Linksys MR7500 support 
Codename: Divo

Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset

Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
  xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.

Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel

2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel

3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel

4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell

Link: openwrt#17428

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
 2025-03-28 12:38:33 +01:00
Chukun Pan
c3f2bb7afc qualcommax: ipq60xx: add GL.iNet GL-AX1800/AXT1800 support 
Specifications:
  SoC:     Qualcomm IPQ6000
  RAM:     512 MiB
  Flash:   128 MiB NAND
  ETH:     Qualcomm QCA8075
  WLAN1:   2.4GHz 802.11b/g/n/ax 2x2
  WLAN2:   5GHz 802.11a/n/ac/ax 2x2
  Button:  Reset, Switch
  USB:     1x 3.0
  SD slot: 1 in GL-AXT1800

Install via stock firmware:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings.

Install via uboot web failsafe:
  Push the reset button for 5 seconds, then use broswer
  to access http://192.168.1.1, and upload factory.ubi.

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
 2025-03-24 10:16:00 +01:00
Scott Mercer
46e376c935 uboot-tools: migrate uboot-envtools to uboot-tools 
Generalize and merge uboot-envtools package into uboot-tools package.
Remove existing uboot-envtools package.

Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
 2025-03-22 13:18:09 +00:00