Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 69890e16b3)
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c87a767801)
Link: https://github.com/openwrt/openwrt/pull/17790
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt76x8 SDXC pin register definition is incompatible with the
mtmips generic pinctrl driver structure. This hack allows us to
mux the SDXC IO to different pin groups in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
(cherry picked from commit 05ec3b50a8)
Link: https://github.com/openwrt/openwrt/pull/17754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The definition for the netgear_wndr4700 had two different
DEVICE_COMPAT_VERSION definitions.
In commit 5815884c3a ("apm821xx: migrate to DSA"), an additional
DEVICE_COMPAT_VERSION := 3.0 attribute was added to the device
definition. The old one with version 2.0 stayed and was defined later
overwriting the new one.
Replace the old version 2.0 with the new version 3.0
Fixes: 5815884c3a ("apm821xx: migrate to DSA")
Link: https://forum.openwrt.org/t/openwrt-24-10-0-rc6-sixth-release-candidate/222466/43
Link: https://github.com/openwrt/openwrt/pull/17741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dab52c00d7)
The STM32MP135F-DK board uses the LAN8742 PHY.
Enable CONFIG_SMSC_PHY to have full PHY support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17745
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d981f28f76)
Since commit f1c9afd801 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd801 for USW-Flex restores full 1 Gbps switching
performance on all ports.
Signed-off-by: Anders Melchiorsen <amelchio@nogoto.net>
Link: https://github.com/openwrt/openwrt/pull/17703
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 62872f8bfd)
Replace clock patch for eMMC with upstream version to add the tag and
flag them as upstreamed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a9b408a97f)
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b7edf88b0f)
Refresh cpufreq with merged upstream version. Also fix the PM Domain
rebased patch to correctly expose the symbol for non Mediatek target.
Update dtsi with new pm domain name.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fbbfcbf150)
The on-device board name reported by 'ubus call system board' is not present
in the generated profiles.json. This results in upgrade tools being unable
to match the image with the proper device. Let's add a 'SUPPORTED_DEVICES'
entry for the board name to fix this.
Links: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/441
Links: 2a07270180
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17736
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7165937c3b)
Fix usage of non-existent 'caldata_patch_mac' function
by using the 'caldata_patch_data' function.
Fixes: #17734
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17737
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3295f6f1c2)
Import patch "net: phy: realtek: mark existing MMDs as present"
When using Clause-45 mode to access RealTek RTL8221B 2.5G PHYs some
versions of the PHY fail to report the MMDs present on the PHY.
Mark MMDs PMAPMD, PCS and AN which are always existing according to
the datasheet as present to fix that.
Fixes: #16823, #17183, #17232
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
(cherry picked from commit 730db6b893)
Fixed interrupt support for 2.5G PHY.
Removed useless phy-mode on phy node.
Tested on Cudy TR3000.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 82b69dfaf6)
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Move the nmbm properties outside the partition definition.
Change uppercase to lowercase, add missing read-only flag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit ab375a3484)
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
CC: John Crispin <john@phrozen.org>
Fixes: cfd42a0098 ("ipq40xx: add Intel/Lantiq ATM hacks")
Suggested-by: Andre Heider <a.heider@gmail.com>
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-4-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6d6dc3a3c9)
the wifi leds of the wax206 were not reacting.
This patch enables the green leds to show activity, as the blue ones are very bright.
Also set the label-mac to the gmac0
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9ada8578fd)
Supported devices are listed in the metadata as the first part of the
DTS compatible. This normally follows the format "vendor,device".
When updating the device name of the 180W 1920-8G PoE an underscore was
used, instead of a comma, to join the vendor and device name. This will
lead to warnings for users wanting to sysupgrade a device with an older
compatible, as the device's info does not match the one the metadata.
Fixes: 987c96e889 ("realtek: rename hpe,1920-8g-poe to match hardware")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 6a7fa68569)
Fixed an issue where both WAN LEDs light up before plugging in the
ethernet cable and no blinking regardless of WAN network activity.
Updated the LED configuration to reflect proper status:
Green indicates 2.5Gb connection speed.
Yellow indicates other connection speed and traffic activity.
This resolves inconsistent WAN LED behavior on Spectrum SAX1V1K routers.
Signed-off-by: Ivan Deng <hongba@rocketmail.com>
Link: https://github.com/openwrt/openwrt/pull/17623
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8e78bc39a3)
This patch has been accepted for linux v6.14 so we can move it from pending
to backport.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 2f2e21a52b)
These patches have been accepted in linux v6.14 instead of v6.13.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 12a07e934c)
Expose the temperature sensor built-into RTL822x 2.5G and 5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 3a189e3831)
Refresh hack patches with make target/linux/refresh.
Fixes: 9508ca44eb ("kernel: backport improvement to page pool fragment handling from 6.7")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit ee730a66e9)
Makes it easier to keep drivers like mt76 in sync with newer versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9508ca44eb)
(cherry picked from commit 478041997f)
1. Import pending patch to fix ramips/mt7621 64MB targets.
2. Do not enable CONFIG_PAGE_POOL_STATS by default.
Signed-off-by: Danila Romanov <pervokur@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 15887235c1)
Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.
Fixes: 1d49310fdb ("ath79: add Cisco Meraki MR18")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17680
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7423e67e1b)
This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users:
Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.
RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function
RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call
I didn't find opened issue for AX3000t. Similar AX3200 issue:
Link: https://github.com/openwrt/openwrt/issues/16347
So, other Xiaomi devices (e.g. Xiaomi WR30U) may also require fix.
Fixes: 7dbcc1215a ("mediatek: filogic: add support for Xiaomi AX3000T")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 42a253c7e8)
This commit replaces multiple fw_setenv calls by the bulk one to reduce
flash writes.
Thanks @Linaro1985 for the idea.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a6b0abf466)
the CWMP account mac is correctly set on the lan device but was not correctly as label-mac
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f9813f41b2)
Devices with wifi (LicheePi RV and MangoPi MQ Pro) were using the
wrong module. Also wpad was missing to enable using the WiFi.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/17576
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
(cherry picked from commit 8a17bae722)
The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before.
This commit changes this to trigger on activity of the respective radio
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17627
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 99431e3150)
Now that LZMA_TEXT_START is configurable per-target once again,
move the target above 32MB boundary for ZTE MF28* devices.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 32c6b9064a)
initramfs for some devices grew so big, that it can't be loaded within
the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable
per-target once again, to fix it for bigger devices, while maintaining
compatibility with previous ones.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6720958659)
Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3d63a41ffa)
This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.
This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).
In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.
However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2cac2a978)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 144af32b47)
This reverts commit 916af73fc3.
It was reported this change did not fix the reboot issues on AR9344.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 937b5a3e00)
Some VRX518 modems fail to initialize properly with the error message
"dc_ep_clk_on failed". As a result, the DSL data path doesn't work.
This hack, which is based on code from the FRITZ!Box 7530 GPL archive,
fixes the issue. It changes the PCIe vendor/device ID to values matching
a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for
connected PCIe devices, by remapping the matching address area to a
specially crafted buffer using the address translation unit.
A dedicated compatible is created to activate this in
the device tree, so this shouldn't affect any devices other than
FRITZ!Box 7530/7520.
Original investigation was done in 59f5212517 which used the "avm,host_magic" property to enabled the patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17622
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 676dcb1b2c)
Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.
So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.
Fixes: 75ad5c2414 ("qualcommax: switch to qca8081 upstream PHY driver")
Fixes: #14502
Link: https://github.com/openwrt/openwrt/pull/17656
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2d077913cd)
These patches have been accepted, so we can move them from pending to
backported.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 7924acdd63)
Import patches to fix several issues with status reporting of RealTek
2.5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 41c164d32b)
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0de9999a78)
Add pending PCI patch that should correctly fix mediatek driver with
Airoha SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f22febae1a)
Backport ETS patch for Airoha ethernet and refresh affected patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 67635578fd)
The package coreutils-stty is not part of the OpenWrt main packages. A
board can not depend on it. Remove the dependency to fix a build problem
seen in the build bots.
Fixes: 8fb805aa1f ("mvebu: Add support for WD Cloud Mirror Gen2")
(cherry picked from commit 717f62d256)
Link: https://github.com/openwrt/openwrt/pull/17589
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
luci-app-attendedsysupgrade expects images to be named
'combined-efi' when the system is using EFI images.
This came about as x86 has 'combined' images for legacy
(BIOS) boot and 'combined-efi' for EFI systems.
armsr images were originally named 'combined' only
as there was no 'legacy' image type.
To avoid special handling in the attendedsysupgrade
code, name EFI images consistent with other targets.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/luci/pull/6430
Link: https://github.com/openwrt/openwrt/pull/12963
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c9ebd4fb30)
When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.
This squashes commit 4357f32d41 ("realtek: debounce reset key for
Zyxel GS1900") and commit 777c6106ed ("realtek: move debounce-interval
to correct node").
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7b9ca01109)
It's missing a hyphen present in every other LED from the set. Set it to
"green:signal-strength-4".
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d04f41e092)
OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.
Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.
Fixes: 5815884c3a ("apm821xx: migrate to DSA")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e9415be4ad)
Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.
Switches used by individual devices are listed below.
Device Switch PHY
Alpha ASL56026 Lantiq GSWIP int. switch
Arcadyan VG3503J Lantiq GSWIP int. switch
Netgear DM200 Lantiq GSWIP int. switch
TP-LINK TD-W8970 Lantiq GSWIP Lantiq PEF7071V
TP-Link TD-W8980 Lantiq GSWIP Lantiq PEF7071V
Reduces uncompressed kernel size by 16 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 517b9c1cdc)
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 524e22b4c7)
The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1b045a7c13)
The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2b4ce1532)
This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).
Fix: #17454
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17575
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1c178f3644)
Refresh DTS with required changes for cpufreq, MTD and MMC. While at it
also fix wrong speed for MAC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17b0d1379a)
Replace cpufreq patch with new version requested upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5069557350)
Add pending patch for ETS qdisc on Airoha ethernet driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53bc763331)
Add patch fixing support for MMC. Additional clock are needed for MMC to
work and some small fixup to make the Mediatek MMC driver on Airoha SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit be5a9ff24b)
Backport patch to support ETS and HTB scheduler for airoha ethernet
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ec3ea5316)
Replace BUS clock patch with upstream version with related tag
as it got approved and merged.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 07b49ce876)
Enable MMC and PCI config symbol and refresh config for Airoha AN7581.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 73d368868c)
Two use AR9287 and one AR9381. Both have different calibration sizes.
Move differences out of wifi node to make it clearer what's what.
qca,no-eeprom needs to stay for 7362sl as there's no nvmem equivalent
for caldata_extract_reverse
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>
These units use AR9287, which has a calibration size of 3d8.
Also fixed compatible string to the proper one to indicate AR9287.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>
The label MAC address is written inside the case of the whw03 v2 at the bottom.
Similar fix as to the 4040 in b22d382ae4
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17535
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c113982706)
Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.
As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.
A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:
- FRITZ!Box 4040
- FRITZ!Box 7530
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/17442
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d09dd75fbd)
This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Backported from f5b1d340be with the exception of
the realtek patch removal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 916af73fc3)
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6992d6e51a)
I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:
Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0
During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`
As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`
As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`
If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.
Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70610a5240)
Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.
Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.
firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.
Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c9ae39b2d1)
We can use a package for the MV88E6060 DSA switch on the single
ath79 device that uses it, saving around 600 KB of memory on
all other devices (for the DSA infrastructure, mainly).
As far as I can see the TP-Link TL WR941 v2 is the only device
using MV88E6060 and the only device with a DSA switch overall.
However the ath79 people should look at this so I'm not
mistaken.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250102-ath79-mv88e6060-module-v1-1-c2a8e31e72fc@linaro.org/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7419381fd)
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 2456a2fd7f)
On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 14be320291)
Now we can set the mt76x8 SDXC pinmux in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b4a9f85c13)
These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0764e30082)
There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:
* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite
For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f5996ae947)
After adding the correct package and pin group configurations,
the SDXC card slot can now function properly.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cea4aae0a9)
In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f70cdfd682)
The upstream mtk-sd driver did not perform specific timing
optimization for MT762x series SoC, hence the SDHC peripheral
of some boards cannot run at too high frequency. Reduce the
maximum clock frequency to fix the mmc read/write error.
Closes: https://github.com/openwrt/openwrt/issues/17364
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17375
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit de0c143742)
Correct a few mistakes around dependencies and naming and unset
CONFIG_FIRMWARE_RP1 in RPi5B's config and instead of a builtin, build it
as a module.
Without this change, there are two entries for rp1.ko in
/lib/modules/$(uname -r)/modules.builtin due to how we strip the leading
directories when we generate it. See: package/kernel/linux/Makefile
around line 63.
% grep rp1.ko /lib/modules/$(uname -r)/modules.builtin
pwm-rp1.ko
clk-rp1.ko
rp1.ko
rp1.ko
The kernel log gets spammed with tons of superfluous warnings as a
results of the double entry:
daemon.warn modprobe: found duplicate builtin module rp1
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17461
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f105d1a9a9)
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0eeba04a16)
Commit 8a477bafb4 backported an upstream patch
without refreshing the patches.
Fixes: 8a477bafb4 ("rockchip: fix phy reset on rk356x")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17474
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 484f670ed3)
The commit 7160820d742a ("phy: rockchip: naneng-combphy: fix phy reset")
was backported to kernel 6.6 branch by upstream, however the correspond
dtsi fixes was not, resulting the following error:
```
[ 0.225521] rockchip-naneng-combphy fe830000.phy: error -ENOENT: failed to get phy reset
[ 0.227467] rockchip-naneng-combphy fe840000.phy: error -ENOENT: failed to get phy reset
```
So backport the dtsi fixes here manually.
Fixes: 89b2356b8c ("kernel: bump 6.6 to 6.6.69")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17468
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8a477bafb4)
defer_list skbs held by NAPI can block releasing page pools.
Work around this by scheduling rx softirq on all CPUs while trying to release
a page pool.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2b70b32aef)
The MAC address of the GMAC is contained inside the CWMP-Account number on the label.
Similar fix as to the 4040 in b22d382ae4
Link #13240
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17467
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2b6955f80)
Robert reported, that in firmware images generated by ASU, there is
`apk` package manager missing after the commit 44598c233d ("build:
remove broken dependency of metadata on toplevel .config variables").
That is happening, because apk got removed from `default_packages` list in
`profiles.json`, which is being generated by `json_overview_image_info` Make
target, which uses `scripts/json_overview_image_info.py` helper script,
which gets the information from `DEFAULT_PACKAGES` Make variable.
So lets fix it by providing `DEFAULT_PACKAGES` variable when its needed.
The reason why we didn't added those packages as a dependency to
base-files like any other packages, was to allow disabling them (in
order to save space).
Fixes: #16969
Fixes: openwrt/asu/issues/1084
Fixes: 44598c233d ("build: remove broken dependency of metadata on toplevel .config variables")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16986
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90f0be8521)
It seems, that handling of DEFAULT_PACKAGES is needed in more places, so
lets move it into dedicated include file so it can be easily shared.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16986
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 40be892a02)
Since the image builder pulls package lists from metadata directly,
add procd and busybox as depdendencies to base-files.
As for the package manager itself, since it can be disabled it needs
to be added directly in the image builder makefile
Fixes: 44598c233d ("build: remove broken dependency of metadata on toplevel .config variables")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4c65359af4)
Add 1920-24g-poe-180w to the mac address retrieval part of 02_network to
properly set the device's port MAC addresses.
This piece was missed when this device was added.
Fixes: b948c1e39b ("realtek: add support for HPE 1920-24G PoE-180W (JG925A)")
Link: https://github.com/openwrt/openwrt/pull/17460
Signed-off-by: James Sweeney <code@swny.io>
(cherry picked from commit 0b54029a6e)
The extraneous closing parenthesis inside the case matching breaks
syntax of the network initialization script 02_network.
/bin/board_detect: /etc/board.d/02_network:
line 40: syntax error: unexpected newline (expecting ")")
Remove this character so board init is functional again.
Fixes: c8ea1aa970 ("realtek: add support for HPE 1920-24G-PoE-370w")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a3391d871d)
Switch to using loader-kernel to accommodate
larger image sizes that are problematic for
many mt7621 uboots.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Link: https://github.com/openwrt/openwrt/pull/17389
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f8a8a2c5c7)
This commit adds kmod-leds-ktd202x to the OpenWrt image for the device
"Acer Connect Vero W6m" which is equipped with one KTD2026 controlling the
device's status LED via I2C.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e44180d45c)
Commit 56d97fff55 backported leds-ktd202x from upstream but didn't add the
generic config symbol.
Fixes: 56d97fff55 ("generic: backport support for KTD2026/7 rgb(w) led controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17396
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c846f48f6a)
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 56d97fff55)
Hardware information: (largely copied from 11275be)
---------------------
The HPE 1920-24G-PoE+ (180W) (JG925A) is a switch that is
part of the 1920 family which has 180W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (180W):
- PoE chip
- 2 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '180'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: James Sweeney <code@swny.io>
Link: https://github.com/openwrt/openwrt/pull/17444
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit b948c1e39b)
Hardware information:
---------------------
The HPE 1920-24G-PoE+ (370W) (JG926A) is a switch that is
part of the 1920 family wich 370W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (370W):
- PoE chip
- 3 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '370'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: Evan Jobling <evan.jobling@mslsc.com.au>
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Link: https://github.com/openwrt/openwrt/pull/17436
[fix space indentation in DTS]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c8ea1aa970)
The HPE JG924A, JG925A and JG926A share the same base.
Prepare base device for adding the PoE enabled switch support.
Signed-off-by: Evan Jobling <evan.jobling@mslsc.com.au>
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Link: https://github.com/openwrt/openwrt/pull/17436
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 41b49a157a)
Netgear Orbi devices rely on ethernet0 alias to be present to U-Boot will
populate the MAC.
This fixes the random MAC on each boot after the ethernet0 alias was
dropped from the SoC DTSI.
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Fixes: #17384
Link: https://github.com/openwrt/openwrt/pull/17414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9ea174c7bf)
Right now there's no way to know what state CFE will leave the pinctrl
registers in, so they should be explicitly set by linux on boot. This
patch adds a gpio configuration for drivers that need it, i.e. gpio-leds.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[improve patch and fix warnings]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit e44daa4fa5)
This reverts commit 15b21c474e.
The issue seems to appear spuriously.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 84ca1c28f7)
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.67..HEAD
(HEAD -> 811ff707533bcd67cdcd368bbd46223082009b12)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 692205305d)
Add kmods for the following RP1 options that not all users
will necessarily need or want compiled in:
* Composite video
* Display video
* LED control
* PWM control
* Serial video
Build system: x86/64
Build-tested: bcm2712/RPi5B
Run-tested: bcm2712/RPi5B
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17233
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d6c5805db3)
Build in several options RP1-specific features rather than
generating additional kmods for them since bcm2712 is unique to
RPi5B only.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17233
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 87309edba4)
Cherry-pick patches to support building RP1 modules.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17233
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 613dd79d5e)
MX30LFxG18AC OTP area access has been fixed upstream:
e87161321a
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 15b21c474e)
Conversion to DSA broke 802.2+LLC+SNAP packet processing. Frames
received by napi_complete_done with GRO and DSA have transport_header
set two bytes short, or pointing 2 bytes before network_header &
skb->data. As snap_rcv expects transport_header to point to SNAP
header (OID:PID) after LLC processing advances offset over LLC header
(llc_rcv & llc_fixup_skb), code doesn't find a match and packet is
dropped.
Image built at this commit operates properly:
86dadeba48 - generic: add patch for GPON-ONU-34-20BI quirk
Image built at following commit exhibits the issue:
337e36e0ef - ipq806x: convert each device to DSA implementation
As issue is LLC specific, to avoid impacting non-LLC traffic, and to
follow up on original assumption made on kernel commit fda55eca5a33
("net: introduce skb_transport_header_was_set()") stating "network
stacks usually reset the transport header anyway", llc_fixup_skb to
reset and advance the offset. llc_fixup_skb already assumes the LLC
header is at skb->data, and by definition SNAP header immediately
follows.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17220
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit da7ab64f1f)
Kernel 6.6 requires LED node names to be prefixed via "led-", otherwise
probing the LED will fail, so update our downstream patch adding the LED.
Signed-off-by: Richard Schneidt <ricsc@users.noreply.github.com>
Link: https://github.com/openwrt/openwrt/pull/17330
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f491001f0c)
Referencing commit a1837135e0
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Nanya NT5TU64M16HG-AC)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
BUTTON: Reset - WPS - "Router" switch
LED: 2x system-LED, 2x wlan-LED, 1x internet-LED,
2x routing-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/17227
(cherry picked from commit 42254d3f5f)
Link: https://github.com/openwrt/openwrt/pull/17359
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
- 3 buttons (WPS, reset, LED on/off)
- 1x 2.5 Gbit WAN port with Maxlinear GPY211C
- 4x 1 Gbit LAN ports
Disassembly:
- There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
- Note that there is another set of 4 pin holes on the side of the board, it's not used.
- Pins (from front to rear):
- 3.3V (do not connect)
- TX
- RX
- GND
- Settings: 115200, 8N1
MAC addresses:
- MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
- MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
- WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
- LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
- WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
- WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)
Flashing via OEM web interface:
- Currently not supported because image crypto is not known
Flashing via recovery web interface:
- This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
- Use a Chromium based browser, otherwise firmware upgrade might not work
- Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
- Upload the recovery image, this will take some time. LED will continue flashing red during the update process
- The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
- If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
- Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
- Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
- OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
- Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used
Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
- This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
- Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
- During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition
Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17296
(cherry picked from commit b3ce08e0b6)
Link: https://github.com/openwrt/openwrt/pull/17363
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).
Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio
Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.
Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
(cherry picked from commit 5a7fb834c7)
Link: https://github.com/openwrt/openwrt/pull/17348
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel logs the error "bcm6368_nand 10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[add bcm636/bcm6368 and fix commit title]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d1e9c50d06)
The GS1900 images have been updated to have a larger firmware partition,
bumping the compatibility version to 2.0. However, since this version is
generated on first boot and the default was used, these images still
advertised 1.0 after a fresh install.
Add a new uci-defaults script that will generate the correct version for
all affected Zyxel GS1900 devices.
Fixes: 35acdbe909 ("realtek: merge Zyxel GS1900 firmware partitions")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a25809a474)
set macaddress correctly for board
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 363f52d067)
The blocksize was too high, resulting in forgetting the config on sysupgrade
It is not needed for SPI-NOR.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 24fc5ff213)
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 35acdbe909)
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 2ada95ccdf)
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4892ea9a74)
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d7f638bc69)
