with more new device, now able to flash oem
images from luci, fwtools erroneously marks
firmware as incompatible and does not warn
across keeping configs during update.
this patch aims to add both oem detection
and a warning msg advising firmware is compatible
(OpenWrt -> OEM) but configuration is not
tested on ipq5018: gl-b3000
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
package: basefiles: add oem image dectection to fwtool
some new devices are now able to flash oem
images from luci, fwtools erroneously marks
firmware as incompatible and does not warn
of keeping configs during update for this condition.
this patch aims to add both oem detection
and trigger the existing warning msg, advising firmware is compatible
(OpenWrt -> OEM) but configuration is not
tested on ipq5018: gl-b3000
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18554
Signed-off-by: Robert Marko <robimarko@gmail.com>
- only run a single poll in the uloop_fd cb to avoid use-after-free on close
- delete the uloop_fd on close
- when calling into ucode, fetch the vm pointer before the call in order
to avoid accessing the stale uline context
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Easy way to add compatibility for kernel 6.12.
Since the linux 3.8 patch undoes a bunch of stuff in platform, just
modiify everything in platform.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18616
Signed-off-by: Robert Marko <robimarko@gmail.com>
YAFFS support in U-Boot is basically abandoned and will even fail to
build with GCC14, so simply disable it.
Link: https://github.com/openwrt/openwrt/pull/18598
Signed-off-by: Robert Marko <robimarko@gmail.com>
uImage.FIT validation was restricted to certain sub-image types
which is problematic as it then won't validate eg. 'filesystem' type
subimages. Also prevent decompressing sub-images into a arbitrary
sized buffer just to then free that buffer -- there is not need to
do this and creating malicious compressed payloads which overflow the
buffer is too easy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since the irq gets copied to sc, it's a really bad idea to use devm,
especially when probe fails.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes: 4e18d22 ("mac80211: ath9k: simplify probe with devm")
Link: https://github.com/openwrt/openwrt/pull/18570
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
[bump release, improve commit description and package changes]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Disable ASPM support for this NIC, fixing strange behavior problems, such as
increased latency, strange uneven throughput, etc.
With this option disabled the NIC achieves stable performance.
Upsteam r8169 driver disables ASPM by default for this NIC.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
[bump release, fix commit description, split 2nd tx queue part]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for ELECOM WRC-X3000GS2 to update "bootdelay" variable
configured as "0" by default when sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes: https://github.com/u-boot/u-boot/compare/v2025.01...v2025.04
Drop patch 100-rockchip-add-FriendlyElec-NanoPi-R3S.patch. U-Boot
upstream now supports this board.
Tested on Radxa ROCK 5B+.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Prevent flashing truncated or otherwise corrupted uImage.FIT images
by verifying checksums and hashes of all sub-images before flashing
using the newly packaged fit_check_sign tool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Introduce special handling for return code 74 (EBADMSG) of
platform_check_image which will mark the image as broken and hence
not allow the user to override the check using the --force option.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
APK is currently broken when built with GCC15 and LTO as it will then hang
indefinitevely on the package/install step.
Luckily, upstream was able to find the issue and fix it, so lets backport
the fix as GCC15 is the default compiler on Fedora 42(And soon more distros)
Link: https://github.com/openwrt/openwrt/pull/18549
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If SYS_statmount/SYS_listmount is not provided by the libc,
util-linux will fall back to __NR_statmount/__NR_listmount from the
kernel UAPI headers.
However it is not guaranteed that these symbols are actually visible in
mount-api-utils.
Include linux/unistd.h which provides syscall numbers.
While this header is specific to Linux, the code is already using
linux/mount.h.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18539
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some ISPs require the client ID to be set in the DHCP and DHCPv6
requests. OpenWrt sets the client id for IPv6 but not for IPv4 by
default.
Align this behavior between DHCPv4 and DHCPv6.
ISPs that require this measure are Deutsche Glasfaser as well as some
Entega connections.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
The nvram file is generic for all stm32 boards, add a symlink for
STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add entry for STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add entry for STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add entry for STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add backport patch that fixes ath12k regdomain parsing failure in
6GHz band triggered by the latest regdb/board-2.bin update.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18512
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previous commits missed some refreshing
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18512
Signed-off-by: Robert Marko <robimarko@gmail.com>
During envtools conversion to the generic uboot-tools package, a syncconfig
call was added to the configure step which was previously not there.
We received multiple spourious reports that now envtools were failing to
build [1], but it was not reproducible.
However, it seems that this could easily be reproduced on MacOS 15 and
somehow that syncconfig call is breaking build by Makefile.autoconf not
being executed and thus no "include/config.h" is generated.
So, since this call was not previously there and U-Boot will actually do
syncconfig on its own when needed lets drop it.
[1] 293d5f1366 (commitcomment-154347516)
Link: https://github.com/openwrt/openwrt/pull/18515
Signed-off-by: Robert Marko <robimarko@gmail.com>
Look for OPENWRT_VERBOSE and pass it down to the U-Boot so we actually
get verbose build info when needed for debugging.
Link: https://github.com/openwrt/openwrt/pull/18515
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix an issue where NCM interface initialization fails because of wrong
modem manufacturer detection.
gcom call returns an output with Windows-style line breaks (containing \r)
what makes awk call return empty or malformed manufacturer name. Changing
awk RS variable to handle both \n and \r\n as line break fixes this issue.
Fixes#17448 and #17998 GitHub issues.
Signed-off-by: Jakub Łabuz <jakub@labuz.dev>
Link: https://github.com/openwrt/openwrt/pull/18460
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update uboot-ath79 package to v2025.04 for ath79 devices.
Additionally, new "CONFIG_NO_NET" option was introduced and replaced
disabled CONFIG_NET option ("# CONFIG_NET is not set"). So replace
that old options in the NEC Aterm devices as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18475
Signed-off-by: Robert Marko <robimarko@gmail.com>
The submenu of two diag modules is missing, fix it.
Fixes: 65de1e0 ("kernel: add missing symbols for lxc")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18480
Signed-off-by: Robert Marko <robimarko@gmail.com>
