Currently the SerDes driven SFP ports give strange ethtool readings
on RTL83xx devices. Especially duplex and speed are shown even if
no link is up and running. That leads to confusion because the MAC
reports arbitrary values.
Enhance the readout by refactoring the pcs_get_state() function.
Calculate speed/duplex/pause only if link is detected. Additionally
add reporting of 10G for SFP+ on RTL839x.
ethtool for empty SFP cage before/after
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ MII ]
Supported link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ MII ]
Supported link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
ethtool with inserted but NOT connected 1G module before/after
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19524
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows building the kmod-drm-ivpu which depends on
CONFIG_DRM_ACCEL. This module is x86_64 only.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-rpi-panel-attiny-regulator and kmod-rpi-panel-7inch-touchscreen
are included in target modules.mk file, they should also depend on the target,
otherwise they can be selected from every target.
Fix the AutoProbe for panel-raspberrypi-touchscreen too.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-imx2-wdt, kmod-imx7-ulp-wdt and kmod-wdt-sp805 are included in
target modules.mk file, they should also depend on the target, otherwise
they can be selected from every target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-ata-dwc is included in target modules.mk file, it should also
depend on the target, otherwise it can be selected from every target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_BCMGENET kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-bcmgenet depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SerDes setup function needs to be called to make 2500Base-X work.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19517
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On some devices (like ZyXEL GS1920) the phys are not initialized and patched
by the bootloader. This is done through the vendor SDK when the software
starts. To make these devices usable too, provide the most basic setup
sequence for the RTL8218B.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19491
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver currently uses two checks to verify the capabilities. These
are ..._phylink_get_caps() and ..._pcs_validate(). For RTL930x these
must allow 2.5G modes. Enhance that as follows:
Add 2500BASEX to phylink_get_caps(). Sort the interfaces alphabetically
and rename the function to the new prefix. IMPORTANT REMARK! Until now
this function allowed the XGMII mode (10G only parallel interface) that
was somehow mixed with the Realtek proprietary mode XSGMII (10G SGMII).
Remove it to avoid further confusion.
Looking upstream pcs_validate() is used less and less. There are only
2 consumers left in 6.16 and the calling location reads:
/* Validate the link parameters with the PCS */
if (pcs->ops->pcs_validate) {
ret = pcs->ops->pcs_validate(pcs, supported, state);
if (ret < 0 || phylink_is_empty_linkmode(supported))
return -EINVAL;
/* Ensure the advertising mask is a subset of the
* supported mask.
*/
linkmode_and(state->advertising, state->advertising,
supported);
}
There is no need for this additional check. Drop the functions.
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file should be generated automatically at runtime by the kernel
build system.
Link: https://github.com/openwrt/openwrt/pull/19473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix bootloop on TP-Link EAP615-Wall v1 by reducing LZMA dictionary
size. Before this patch and after an upgrade to kernel 6.12 this
device couldn't boot a kernel because of an error: "lzma compressed:
uncompress error 1".
I have chosen -d22 as dictionary size as suggested by @namiltd.
The usual sizes for problematic devices are -d16, -d20, -d22. I
have confirmed with my tests that this device can boot with a value
up to -d27, but there is no size benefit from values above -d21,
therefore -d22 is good enough.
See also: https://github.com/openwrt/openwrt/issues/19403
Signed-off-by: Marcin FM <marcin@ipv8.pl>
Link: https://github.com/openwrt/openwrt/pull/19433
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some NanoPC-T6 boards with A3A444 eMMC chips experience I/O errors and
corruption when using HS400 mode. Downgrade to HS200 mode to ensure
stable operation.
Fixes: #18844
Signed-off-by: Grzegorz Sterniczuk <grzegorz@sternicz.uk>
Link: https://github.com/openwrt/openwrt/pull/19398
[Add patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit increases the SPI bus frequency from 20 to 52 MHz. Reduces boot
time by 2s. Below is a performance comparison.
Before:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 2 s, 5.8 MB/
After:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 1 s, 9.7 MB/s
Taken from PR #18752 as each device should be tested individually, so I have
created a separate PR for this.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the switch to Linux 6.12 this driver was enabled by accident.
However, it doesn't support any of the router SoCs but is meant to be
used only by the smartphone, tablet and chromebook SoCs.
Disable the driver again to silence a kernel error logline during boot.
Fixes: 0a0f5f94ec ("mediatek: mt7623: update config-6.12")
Fixes: 029b7ed9c4 ("mediatek: mt7622: update config-6.12")
Reported-by: https://aparcar.org/openwrt-tests/119/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add new mtdsplit parser "mstc-boot" for the devices manufactured by MSTC
(Mitra Star Technology Corp.). This is necessary to handle dual-boot on
those devices.
This parser splits kernel+rootfs or only rootfs(or UBI) based on the
image in the firmware partition or pre-defined partitions in dts, and
"bootnum" value in the "persist" (or "working") partition.
Note: "bootnum" is used for switching active firmware partitions on the
devices manufactured by MSTC and '1' or '2' are used on most
devices. But some devices use '0' or '1'. (example: I-O DATA
WN-DEAX1800GR)
Sequence:
1. obtain "bootnum" value
2. child nodes exsist (regardless of bootnum)
-> fixed partitions
(active parts : without bootnum (ex.: "kernel", "rootfs")
inactive parts: with bootnum (ex.: "kernel2", "rootfs2"))
3. current partition is active (dt bootnum == mtd bootnum)
-> image-based partitions
Device Tree:
- common
- mstc,bootnum : "bootnum" value for the mtd partition (0/1/2)
- mstc,persist : phandle of "persist" partition containing "bootnum"
value
- fixed partitions
- #address-cells: indicate cell count of address of child nodes (1)
- #size-cells : indicate cell count of size of child nodes (1)
- (child nodes) : define the child partitions
- reg : define the offset and size
- label-base : define the base name of the partition
- (example) : base:"kernel"->"kernel"(active)/"kernel2"(inactive)
example:
partition@3c0000 {
compatible = "mstc,boot";
reg = <0x3c0000 0x3240000>;
label = "firmware1";
mstc,bootnum = <1>;
mstc,persist = <&mtd_persist>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x800000>;
label-base = "kernel";
};
partition@800000 {
reg = <0x800000 0x2a40000>;
label-base = "ubi";
};
};
- image-based partitions
(no additional properties)
example:
partition@5a0000 {
compatible = "mstc,boot";
label = "firmware1";
reg = <0x5a0000 0x3200000>;
mstc,bootnum = <1>;
mstc,persist = <&mtd_persist>;
};
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18976
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The 6.12 testing kernel for ipq40xx target is ready now.
Tested on SKSpruce WIA3300-20.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the ipq40xx platform, the bus range is 1 - 255. Therefore, bus
number 0 is clearly incorrect. Change the bus number to 1, just
like other ipq40xx devices. This patch fixes the following dtc
warnings on 6.12 kernel:
qcom-ipq4019.dtsi:476.5-29: Warning (pci_device_bus_num): /soc/pcie@40000000/pcie@0/wifi@0,0:bus-range: PCI bus number 0 out of range, expected (1 - 255)
qcom-ipq4019.dtsi:476.5-29: Warning (pci_device_bus_num): /soc/pcie@40000000/pcie@0/wifi@0,0:bus-range: PCI bus number 0 out of range, expected (1 - 255)
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Remove duplicate PCIe bridge. A default bridge node has been
added upstream.
- Do not refer to the qca807x node. This node label has been
removed. We can disable the qca807x phy in mdio node.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a bridge node label so that we can insert PCIe peripheral nodes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy arch directory from 6.12 kernel to restore the default
6.6 device tree files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy patches and kernel configs from 6.12 kernel to restore the
default 6.6 kernel support files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for 6.12 kernel support. It can help us
track the device tree files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for 6.12 kernel support. It can help us
track the patches and Kconfig history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for introducing the 6.12 kernel support.
All configs are automatically refreshed. In theory, they will
generate the same .config files in the kernel build directory
as before.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The prototype of `devm_platform_ioremap_resource_byname()` was defined
in `linux/platform_device.h`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This function is only used by the current source file gcc-ipq4019.c.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The node name should include the reg property value. Fix warning:
qcom-ipq4019-lbr20.dts:415.17-449.4: Warning (i2c_bus_reg): /soc/i2c@78b7000/led-controller: I2C bus unit address format error, expected "27"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18725
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Not all targets support power management, some older or more simple
targets don't have CONFIG_PM set. Allow kernel module packages to
depend on USES_PM to only be available on targets which got
CONFIG_PM=y in their kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The files-6.6 and files-6.12 folder contain the same content, merge them
into the files folder for both kernel versions.
Link: https://github.com/openwrt/openwrt/pull/19423
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ix4-200d is a 4 bay NAS supported since OpenWrt 23.05. Drive trays
controller. Due to a kernel-related issue with the SATA controller,
trays #1 and #2 were not recognized. This issue has been fixed in
kernel 6.10, so with the adoption of kernel 6.12 in the Kirkwood
target trays #1 and #2 can now be made accessible. This requires the
kmod-ata-ahci package, which this commit adds as default to the
makefile.
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/19435
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Not all targets have CONFIG_PINCTRL=y set in their kernel config.
Let's introduce a feature for that so kernel module packages which
select or depend on CONFIG_PINCTRL=y may depend on that, so we can
try to prevent leaking CONFIG_PINCTRL=y also into targets which do
not require it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
