mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2026-01-30 07:26:21 -05:00
736494deeca2da5f17ee244cb8440856ce4d7ce4
12 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Markus Stockhausen
|
f88135b7cd |
realtek: add support for Linksys LGS352C
Hardware specification ---------------------- * RTL9311 SoC, 2 MIPS Interaptiv cores @ 1000MHz * 512MB DRAM * 2MB NOR Flash * 128MB NAND Flash * 48 x 10/100/1000BASE-T ports * 4 x 10G SFP+ ports * LM63 controlled fan * Power LED, Fault LED * Reset button on front panel * UART (115200 8N1) via RJ45 Installation using serial interface ----------------------------------- 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Start network "rtk network on" 3. Load image "tftpboot <TFTP IP>:openwrt-realtek-rtl931x_nand-linksys_lgs352c-initramfs-kernel.bin" 4. Boot image "bootm" 5. Switch to first bootpartition "fw_setsys bootpartition 0" 5. Download sysupgrade "scp <IP>:openwrt-realtek-rtl931x_nand-linksys_lgs352c-squashfs-sysupgrade.bin /tmp/." 6. Install sysupgrade "sysupgrade /tmp/openwrt-realtek-rtl931x_nand-linksys_lgs352c-squashfs-sysupgrade.bin" Installation using OEM webinterface ----------------------------------- This is not possible because the OpenWrt NAND Flash layout is different from the vendor layout. To be precise. Vendor uses: - 64 MB vendor UBI root_data - 32 MB vendor kernel+root 1 (~19 MB used) - 32 MB vendor kernel+root 2 (~19 MB used) OpenWrt uses: - 64 MB vendor UBI (not touched) - 10 MB OpenWrt kernel - 22 MB Openwrt mtd-concat UBI - 23 MB vendor kernel 2 (space reduced, vendor data unchanged) - 09 MB OpenWrt mtd-concat UBI Dual-boot with stock firmware using writable u-boot-env ------------------------------------------------------- From stock to OpenWrt / primary image 1 (CLI as admin): - > boot system image1 - > reboot From OpenWrt to stock / boot image 2: (shell as root) - # fw_setsys bootpartition 1 - # reboot Debrick using serial interface ------------------------------ 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Load vendor image with "upgrade runtime <TFTP IP>:LGS352xxxxx.imag" 3. switch to primary partition "setsys bootpartition 0" 4. safe config "savesys" Further documentation --------------------- See https://openwrt.org/toh/linksys/lgs352c Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/20255 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Markus Stockhausen
|
853d73f9d1 |
realtek: add support for Linksys LGS328C
Hardware specification ---------------------- * RTL9301 SoC, 1 MIPS 34KEc core @ 800MHz * 512MB DRAM * 2MB NOR Flash * 128MB NAND Flash * 24 x 10/100/1000BASE-T ports * 4 x 10G SFP+ ports * Power LED, Fault LED * Reset button on front panel * UART (115200 8N1) via RJ45 Installation using serial interface ----------------------------------- 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Start network "rtk network on" 3. Load image "tftpboot <TFTP IP>:openwrt-realtek-rtl930x_nand-linksys_lgs328c-initramfs-kernel.bin" 4. Boot image "bootm" 5. Switch to first bootpartition "fw_setsys bootpartition 0" 5. Download sysupgrade "scp <IP>:openwrt-realtek-rtl930x_nand-linksys_lgs328c-squashfs-sysupgrade.bin /tmp/." 6. Install sysupgrade "sysupgrade /tmp/openwrt-realtek-rtl930x_nand-linksys_lgs328c-squashfs-sysupgrade.bin" Installation using OEM webinterface ----------------------------------- This is not possible because the OpenWrt NAND Flash layout is different from the vendor layout. To be precise. Vendor uses: - 64 MB vendor UBI root_data - 32 MB vendor kernel+root 1 (~19 MB used) - 32 MB vendor kernel+root 2 (~19 MB used) OpenWrt uses: - 64 MB vendor UBI (not touched) - 10 MB OpenWrt kernel - 22 MB Openwrt mtd-concat UBI - 23 MB vendor kernel 2 (space reduced, vendor data unchanged) - 09 MB OpenWrt mtd-concat UBI Dual-boot with stock firmware using writable u-boot-env ------------------------------------------------------- From stock to OpenWrt / primary image 1 (CLI as admin): - > boot system image1 - > reboot From OpenWrt to stock / boot image 2: (shell as root) - # fw_setsys bootpartition 1 - # reboot Debrick using serial interface ------------------------------ 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Load vendor image with "upgrade runtime <TFTP IP>:LGS328xxxxx.imag" 3. switch to primary partition "setsys bootpartition 0" 4. safe config "savesys" Further documentation --------------------- See https://openwrt.org/toh/linksys/lgs352c Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/20255 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Harshal Gohel
|
ce8ea739eb |
realtek: rtl931x: Add support for Plasma Cloud ESX28 Switch
The Plasma Cloud ESX28 Switch is a 24 + 4 port multi-GBit switch with
24x 10/100/1000/2500BaseT Ethernet ports and 4x SFP+ module slot.
Hardware:
- RTL9312C SoC
- Macronix MX25L25645G (32MB flash)
- 512MB DDR3 SDRAM
- RTL8231 GPIO extender to control the port LEDs
- 6x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 4x 10GBit slot
The switch is powered directly via AC.
The external RS232 serial connector (RJ45, Cisco pinout) can be used to
access the terminal. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial on front panel. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl931x-plasmacloud_esx28-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl931x-plasmacloud_esx28-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x5e0000 0x1a20000
# write firmware to both partitions
sf write ${fileaddr} 0x5e0000 ${filesize}
sf write ${fileaddr} 0x12f0000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:768k(u-boot),64k(u-boot-env),64k(u-boot-env2),5120k(reserved),13376k(inactive),13376k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb52f0000"
# restart
reset
Debug
-----
* Connect serial on front panel. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enter passwords: "1234" or "plasmapsx"
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl931x-plasmacloud_esx28-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Harshal Gohel
|
2b5555c195 |
realtek: rtl931x: Add support for Plasma Cloud PSX28 Switch
The Plasma Cloud PSX28 Switch is a 24 + 4 port multi-GBit switch with
24x 10/100/1000/2500BaseT Ethernet ports and 4x SFP+ module slot.
Hardware:
- RTL9312C SoC
- Macronix MX25L25645G (32MB flash)
- 512MB DDR3 SDRAM
- RTL8231 GPIO extender to control the port LEDs
- 6x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 4x 10GBit slot
- RTL8239 POE++ PSE controller with frontend MCU
The switch is powered directly via AC.
The external RS232 serial connector (RJ45, Cisco pinout) can be used to
access the terminal. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial on front panel. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl931x-plasmacloud_psx28-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl931x-plasmacloud_psx28-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x5e0000 0x1a20000
# write firmware to both partitions
sf write ${fileaddr} 0x5e0000 ${filesize}
sf write ${fileaddr} 0x12f0000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:768k(u-boot),64k(u-boot-env),64k(u-boot-env2),5120k(reserved),13376k(inactive),13376k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb52f0000"
# restart
reset
Debug
-----
* Connect serial on front panel. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enter passwords: "1234" or "plasmapsx"
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl931x-plasmacloud_psx28-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Harshal Gohel
|
cb4603688b |
realtek: rtl930x: Add support for Plasma Cloud PSX10 Switch
The Plasma Cloud PSX10 Switch is a 8 + 2 port multi-GBit switch with
8x 10/100/1000/2500BaseT Ethernet ports and 2x SFP+ module slot.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6NB-12 (256MB DDR3 SDRAM - only 128 MB configured*)
- 2x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 2x 10GBit slot
- IC+ IP8008 POE+ PSE controller
The switch is powered by 54 Volts 2.77A barrel connector. The internal TTL
serial connector can be used to access the terminal. Pins from 1: TX RX
(unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
*) Only 128 MB of RAM are currently configured because there were
infrequent random memory corruptions detected when using memtester with a
256 MB DT configuration. This could also be reproduced with RTLSDK.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_psx10-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_psx10-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_psx10-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Harshal Gohel
|
e677da90d1 |
realtek: rtl930x: Add support for Plasma Cloud PSX8 Switch
The Plasma Cloud PSX8 Switch is a 8 port multi-GBit switch with
8x 10/100/1000/2500BaseT Ethernet ports.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6NB-12 (256MB DDR3 SDRAM - only 128 MB configured*)
- 2x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- IC+ IP8008 POE+ PSE controller
The switch is powered by 54 Volts 2.77A barrel connector. The internal TTL
serial connector can be used to access the terminal. Pins from 1: TX RX
(unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
*) Only 128 MB of RAM are currently configured because there were
infrequent random memory corruptions detected when using memtester with a
256 MB DT configuration. This could also be reproduced with RTLSDK.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_psx8-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_psx8-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_psx8-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Harshal Gohel
|
7812d867b4 |
realtek: Introduce Plasma Cloud sysupgrade helper
Plasma Cloud devices use a dual-firmware regions/slots boot mechanism. On
APs, the u-boot is "intelligent" and checks the NOR/NAND partitions (kernel
+ rootfs) for corruption via "datachk". If validation fails, the bootloader
automatically switches to the fallback partition.
On Realtek-based switches, this "datachk" helper is not available.
However, the bootloader still supports two firmware regions/slots.
When flashing a new image, the "inactive" partition is written instead of
overwriting the active one. If no "inactive" partition exists but
"firmware1" is present, the bootloader always treats "firmware1" as
fallback. Only after a successful flash is the `u-boot-env` updated to
select the newly written partition.
On reboot, the bootloader loads the kernel from the new partition and
passes `mtdparts` information as the kernel cmdline. The Plasma Cloud
switch device tree does not override this with a `bootargs` property, so
the active partition layout is honored from cmdline.
Since offsets, sizes, and names of partitions match between the device tree
and cmdline (except the inactive slot), properties and nodes such as
`nvmem-cells` or `compatible` remain fully usable.
This mechanism also allows switching back to the old firmware slot. For
example, if `firmware1` is currently active (`/proc/mtd` shows it), it can
be switched to slot 2 using:
. /lib/upgrade/upgrade_dualboot.sh
set_boot_part 2
reboot
Firmware upgrades use standard `sysupgrade` tarballs, chosen for
compatibility with vendor images. In theory, one can switch between vendor
and OpenWrt with:
sysupgrade -n /tmp/*-squashfs-sysupgrade.bin
Note: configuration files must not be preserved, as they are not compatible
with vanilla OpenWrt.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
Alexandru Gagniuc
|
01e2184c49 |
realtek: add support for TP-Link SG2210P
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.
This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.
Specifications:
---------------
- SoC: Realtek RTL8380M
- Flash: 32 MiB SPI flash (Vendor varies)
- RAM: 256 MiB (Vendor varies)
- Ethernet: 8x 10/100/1000 Mbps with PoE (all ports)
2x SFP ports
- Buttons: 1x "Reset" button on front panel
- Power: 53.5V DC barrel jack
- UART: 1x serial header, unpopulated
- PoE: 2x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP ports (with caveats)
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE LEDs
Enabling SFP ports:
-------------------
The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.
However, to enable the lasers on SFP1 and SFP2 respectively:
echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWrt.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
|
Alexandru Gagniuc
|
6d5873a162 |
realtek: add support for TP-Link SG2008P
Add support for the TP-Link SG2008P switch. This is an RTL8380 based switch with 802.3af one the first four ports. Specifications: --------------- * SoC: Realtek RTL8380M * Flash: 32 MiB SPI flash (Vendor varies) * RAM: 256 MiB (Vendor varies) * Ethernet: 8x 10/100/1000 Mbps with PoE on 4 ports * Buttons: 1x "Reset" button on front panel * Power: 53.5V DC barrel jack * UART: 1x serial header, unpopulated * PoE: 1x TI TPS23861 I2C PoE controller Works: ------ - (8) RJ-45 ethernet ports - Switch functions - System LED Not yet enabled: ---------------- - Power-over-Ethernet (driver works, but doesn't enable "auto" mode) - PoE, Link/Act, PoE max and System LEDs Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The footprints R27 (0201) and R28 (0402) are not populated. To enable serial console, 50 ohm resistors should be soldered -- any value from 0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge. The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. The sysupgrade image can also be flashed. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U7) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as sson as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U7) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> |
||
Thomas Nixon
|
cdb5acac20 |
Revert "realtek: Fix failsafe mode"
This reverts commit
|
||
Hauke Mehrtens
|
b7ee0786b5 |
realtek: Fix failsafe mode
The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is configured. Do not use the standard failsafe configuration for DSA accessing the default port directly, but configure a switch on the lan1 interface instead. This will add the VLAN ID 1 configuration to the switch: $ bridge vlan show port vlan-id lan1 1 PVID Egress Untagged switch 1 PVID Egress Untagged Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
John Crispin
|
2b88563ee5 |
realtek: update the tree to the latest refactored version
* rename the target to realtek * add refactored DSA driver * add latest gpio driver * lots of arch cleanups * new irq driver * additional boards Signed-off-by: Bert Vermeulen <bert@biot.com> Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: John Crispin <john@phrozen.org> |