Hardware
--------
SOC: MediaTek MT7981
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND
WIFI: Mediatek MT7915 (integrated) 2x2 802.11ax 2.4 / 5 GHz
ETH: Mediatek MT7981 internal 1 GbE PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the EAX17. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Jascha Sundaresan <flizarthanon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20354
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Product name: Wavlink WL-WN536AX6 Rev a "Mighty LX2"
Product link: https://www.wavlink.com/en_us/product/WL-WN536AX6.html
Specifications:
SOC: MT7986AV
RAM: 512MB DDR4
Flash: 128MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976PN + MT7975N
LEDs: 8 (STATUS, WIFI, WAN, LAN1, LAN2, LAN3, LAN4, PWR)
USB: 1 (3.0)
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3
5G: 80:3F:5D:xx:xx:x4
* Installation with OEM WebUI:
Note: Make sure PC is connected on LAN1 port. The OEM firmware has an unknown root password and settings are kept after upgrading firmware. Therefore, a customized Openwrt firmware is needed to remove the root password on login, by adding `passwd -d root` to /etc/init.d/bootcount. The WebUI does a filename check so the customized firmware is named accordingly.
1. Download modified firmware file `WAVLINK_WN536AX6-A_M36AX6_V250320-WO-437baca-modified.bin` from https://github.com/ses1er/firmware-misc/tree/main/wavlink/wl-wn536ax6a
2. Log into WebUI on default IP: http://192.168.20.1
3. Browse to More (top menu) -> System -> Firmware Upgrade.
4. Under `Local Upgrade` section, check the device to be upgraded and upload downloaded modified firmware. Click `UPLOAD FILE`, then `APPLY`
5. Wait about 2 minutes (ignore progress bar), and browse to http://192.168.20.1. You should see LUCI login page. Username is root and no password.
6. Browse to `System -> Backup/Flash Firmware`, click on `Flash Image`, click `Browse` and locate `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` file.
7. Uncheck `Keep settings and retain the current configuration` and click `Continue`.
8. Router will now be set to IP 192.168.1.1 which is the Openwrt default.
* Installation with UART:
Note: Having UART connected while cold booting the device will result in a kernel panic when initializing wifi. I've found this workaround:
1. Power off the device and ensure UART is not connected to PC.
2. Power up the device, when lights come on, plug in UART.
3. Warm boots and soft restarts will not cause kernel panic for the duration of device being powered on. Repeat steps for subsequent cold boots.
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-wavlink_wl-wn536ax6a-initramfs.itb` to TFTP root.
2. Interrupt boot by pressing 0.
3. Run the following in Uboot console: `setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-initramfs.itb; bootm`
4. Transfer `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` to device:
(`scp -O openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/`)
5. Run the following on device: `sysupgrade -n /tmp/openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin`
Signed-off-by: Qing W. <ses1er@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/20760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace hardcoded numbers with the dt-bindings drive strength macros
defined in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sources files should used for the proper indentation:
* use tabs instead of 8 spaces
* spaces should never directly before a tab
* no whitespace characters at the end of a line
These rules were partially not followed in various source files.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/20895
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_DRM_MICROCHIP_LVDS_SERIALIZER needs to be added
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19471
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19471
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Link: https://github.com/openwrt/openwrt/pull/20857
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Link: https://github.com/openwrt/openwrt/pull/20856
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Link: https://github.com/openwrt/openwrt/pull/20855
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These patches have been accepted in netdev-next for linux v6.19.
2b3013ac0302 net: dsa: b53: add support for bcm63xx ARL entry format
300f78e8b6b7 net: dsa: b53: add support for 5389/5397/5398 ARL entry format
a7e73339ad46 net: dsa: b53: move ARL entry functions into ops struct
e0c476f325a8 net: dsa: b53: split reading search entry into their own functions
1716be6db04a net: dsa: b53: provide accessors for accessing ARL_SRCH_CTL
bf6e9d2ae1db net: dsa: b53: move writing ARL entries into their own functions
4a291fe72267 net: dsa: b53: move reading ARL entries into their own function
a6e4fd38bf2f net: dsa: b53: b53_arl_read{,25}(): use the entry for comparision
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These patches have been accepted for linux v6.18.
e57723fe536f net: dsa: b53: properly bound ARL searches for < 4 ARL bin chips
674b34c4c770 net: dsa: b53: fix ageing time for BCM53101
89eb9a62aed7 net: dsa: b53: fix reserved register access in b53_fdb_dump()
61730ac10ba9 net: dsa: b53: mmap: Implement bcm63268 gphy power control
7f95f04fe190 net: dsa: b53: mmap: Add gphy port to phy info for bcm63268
5ac00023852d net: dsa: b53: mmap: Implement bcm63xx ephy power control
e8e13073dff7 net: dsa: b53: mmap: Add register layout for bcm6368
c251304ab021 net: dsa: b53: mmap: Add register layout for bcm6318
aed2aaa3c963 net: dsa: b53: mmap: Add syscon reference and register layout for bcm63268
fcf02a462fab net: dsa: b53: Define chip IDs for more bcm63xx SoCs
be7a79145d85 net: dsa: b53: Add phy_enable(), phy_disable() methods
762e7e174da9 net: dsa: tag_brcm: do not mark link local traffic as offloaded
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
A considerable amount of b53 patches has been backported to 6.12, so we
can rename and group the remaining ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This board is also as known as LC-HX3001
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Foresee F35SQA001G 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
Method 1:
1. Connect UART Adapter to the router
2. UART pins are enabled, set the root password with passwd command
start the dropbear instance on port 22
Method 2:
1. Login into web interface, and restore the router with SSH enabled configuration.
2. After reboot Default Web interface password will be 12345678
SSH password is empty
Flash instructions:
1. Connect to HX21, backup everything, especially 'Factory' part.
3. Write new FIP:
mtd write openwrt-mediatek-filogic-hx_21-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
8. To write new BL2
Install mtd-rw
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd write openwrt-mediatek-filogic-imou_hx21-preloader.bin bl2
Signed-off-by: Jahidul Islam <hello@jahid.io>
Link: https://github.com/openwrt/openwrt/pull/20753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With previous patches these devices have only 128 KiB less space than
RE450 v3. It may be even possible to revert commit 65b6f1c1b2 ("ath79:
move TP-Link RE450 v1 & v2 and RE355 v1 to tiny target") but that was
not done as the device has only 8 MiB flash and will eventually run out of
it anyway.
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch utilizes unused and empty flash space in the original partition
layout and increase maximum image size by 1664 KiB.
Tested on RE450v1 by running sysupgrade with build of size 5697 KiB and
checking that df shows 1988 1K-blocks for "/overlay".
Inspired by commit ebd5e5fb53 ("ramips: switched TP-Link RE305 v1 to new
partition layout").
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dump of content of my RE450 v1 showed, that there are valid data only
up to 0x10420. Everything after is just 0xFF. This will also make
partition table identical to qca9563_tplink_re450-v2.dts, which seems
to be logical.
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for D-Link DIR-2660 A2.
Based on the commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b5dd746cbb1aaf91f4b68e9f3eda97413550d904,
Both devices look identical, except for the A1/A2 designation.
You can safely install the A1 firmware for the A2 – I've been testing it for several months as a DUMB AP – without any problems.
Specifications:
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20020
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit ade045084b.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a51359aafd.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 6fa1775348.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 5aab294726.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Trim whitespaces while at it.
1. https://github.com/immortalwrt/immortalwrt/issues/2123#issuecomment-3523744128
Fixes: c908fc7d95 ("mediatek: add support for Zbtlink ZBT-Z8102AX v2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header hole on PCB
- 3.3V, RX, GND, TX (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber/Blue)
1x Wi-Fi (Amber/Blue)
1x WAN activity (Amber/Blue)
4x LAN activity (Amber/Blue)
- Power : 12VDC, 1A (Center positive polarity)
Note: The LED color is amber or blue, depending on your router's color
(black/white).
MAC address
-----------
+-----------+-------------------+-----------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------+
| WLAN 2.4G | B0:38:6C:xx:xx:xx | label |
| WLAN 5G | B2:38:6C:4x:xx:xx | |
| WAN | B0:38:6C:xx:xx:xx | label + 1 |
| LAN | B0:38:6C:xx:xx:xx | label + 3 |
+-----------+-------------------+-----------+
The WLAN 2.4G MAC address was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Limitation: Triggering the WLAN LED for activity on both phy0 (2.4GHz) and phy1 (5GHz)
----------
Currently, the UCI doesn't support triggering a single LED for activity
on multiple WLAN interfaces. As a temporary workaround, the LED is
configured to only indicate activity on `phy1`. If you wish to monitor
`phy0` instead, you must change the device from `phy1-ap0` to `phy0-ap0`
in the LuCI LED configuration.
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use latest patch version
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20400
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no reason not to do this.
Use the following commands to enable hardware offloading:
uci set firewall.@defaults[0].flow_offloading='1'
uci set firewall.@defaults[0].flow_offloading_hw='1'
uci commit
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport changes to the pinctrl driver to bring it closer to
the upstream version. Also fix the bug in the pinctrl driver:
pinctrl-airoha ...pinctrl: invalid function mdio in map table
Fixes: bd7f5b3 ("airoha: replace AN7583 pinctrl patch with upstream version")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The I2C and UART patch numbers are duplicates
of other patches, so reordered them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes the "mdio_bus stmmac-1: MDIO device at address 1 is missing" error
that occurs during cold boot when initializing GMAC.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set KERNEL_TESTING_PATCHVER to allow testing Linux 6.12.
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move back to .remove from .remove_new as kernel 6.12 unified the usage
of .remove and .remove_new (and .remove_new is expected to be dropped in
later version)
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
[ improve commit description ]
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Apply trivial fixes for 6.12 files:
- Make functions static
- Add lots of missing header in drivers
- Fix no newline at end of file error and other new line error
- Drop deprecated validate function for xgmac
- Use devm for stmmac probe
- Remove host_ prefix from pcie_host_ops
Tested-by: Jingkun Zheng <mx@kevinmx.top>
Tested-by: Zhu Yujie <libriunc@gmail.com>
Tested-by: Chuanhong Guo gch981213@gmail.com
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
[ improve commit description ]
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
