With previous patches these devices have only 128 KiB less space than
RE450 v3. It may be even possible to revert commit 65b6f1c1b2 ("ath79:
move TP-Link RE450 v1 & v2 and RE355 v1 to tiny target") but that was
not done as the device has only 8 MiB flash and will eventually run out of
it anyway.
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch utilizes unused and empty flash space in the original partition
layout and increase maximum image size by 1664 KiB.
Tested on RE450v1 by running sysupgrade with build of size 5697 KiB and
checking that df shows 1988 1K-blocks for "/overlay".
Inspired by commit ebd5e5fb53 ("ramips: switched TP-Link RE305 v1 to new
partition layout").
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dump of content of my RE450 v1 showed, that there are valid data only
up to 0x10420. Everything after is just 0xFF. This will also make
partition table identical to qca9563_tplink_re450-v2.dts, which seems
to be logical.
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/20709
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for D-Link DIR-2660 A2.
Based on the commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b5dd746cbb1aaf91f4b68e9f3eda97413550d904,
Both devices look identical, except for the A1/A2 designation.
You can safely install the A1 firmware for the A2 – I've been testing it for several months as a DUMB AP – without any problems.
Specifications:
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20020
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit ade045084b.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a51359aafd.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 6fa1775348.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 5aab294726.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Trim whitespaces while at it.
1. https://github.com/immortalwrt/immortalwrt/issues/2123#issuecomment-3523744128
Fixes: c908fc7d95 ("mediatek: add support for Zbtlink ZBT-Z8102AX v2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header hole on PCB
- 3.3V, RX, GND, TX (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber/Blue)
1x Wi-Fi (Amber/Blue)
1x WAN activity (Amber/Blue)
4x LAN activity (Amber/Blue)
- Power : 12VDC, 1A (Center positive polarity)
Note: The LED color is amber or blue, depending on your router's color
(black/white).
MAC address
-----------
+-----------+-------------------+-----------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------+
| WLAN 2.4G | B0:38:6C:xx:xx:xx | label |
| WLAN 5G | B2:38:6C:4x:xx:xx | |
| WAN | B0:38:6C:xx:xx:xx | label + 1 |
| LAN | B0:38:6C:xx:xx:xx | label + 3 |
+-----------+-------------------+-----------+
The WLAN 2.4G MAC address was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Limitation: Triggering the WLAN LED for activity on both phy0 (2.4GHz) and phy1 (5GHz)
----------
Currently, the UCI doesn't support triggering a single LED for activity
on multiple WLAN interfaces. As a temporary workaround, the LED is
configured to only indicate activity on `phy1`. If you wish to monitor
`phy0` instead, you must change the device from `phy1-ap0` to `phy0-ap0`
in the LuCI LED configuration.
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use latest patch version
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20400
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no reason not to do this.
Use the following commands to enable hardware offloading:
uci set firewall.@defaults[0].flow_offloading='1'
uci set firewall.@defaults[0].flow_offloading_hw='1'
uci commit
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport changes to the pinctrl driver to bring it closer to
the upstream version. Also fix the bug in the pinctrl driver:
pinctrl-airoha ...pinctrl: invalid function mdio in map table
Fixes: bd7f5b3 ("airoha: replace AN7583 pinctrl patch with upstream version")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The I2C and UART patch numbers are duplicates
of other patches, so reordered them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes the "mdio_bus stmmac-1: MDIO device at address 1 is missing" error
that occurs during cold boot when initializing GMAC.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The generic-rk3568 does not reset the gmac phy, causing the kernel to
fail to initialize gmac during cold boot with the error message
"mdio_bus stmmac-1: MDIO device at address 1 is missing."
Adding a dedicated uboot for EasePi R1 to resolve this issue.
The EasePi R1's DTS hasn't been merged into the Linux release yet,
so it cannot be submitted to the upstream u-boot.
Fixes: ef093299db ("uboot-rockchip: add support for LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
this change allows one to selectively "hush" scripts from /etc/profile.d/ directory.
e.g., to skip "opkg to apk cheatsheet" message ("/etc/profile.d/apk-cheatsheet.sh") create empty file "/etc/profile.d/apk-cheatsheet.hush" using, for example, command "touch /etc/profile.d/apk-cheatsheet.hush"
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19953
Signed-off-by: Robert Marko <robimarko@gmail.com>
- move extra parts to /etc/profile.d/*
- improve syntax and messages
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19953
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set KERNEL_TESTING_PATCHVER to allow testing Linux 6.12.
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move back to .remove from .remove_new as kernel 6.12 unified the usage
of .remove and .remove_new (and .remove_new is expected to be dropped in
later version)
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
[ improve commit description ]
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Apply trivial fixes for 6.12 files:
- Make functions static
- Add lots of missing header in drivers
- Fix no newline at end of file error and other new line error
- Drop deprecated validate function for xgmac
- Use devm for stmmac probe
- Remove host_ prefix from pcie_host_ops
Tested-by: Jingkun Zheng <mx@kevinmx.top>
Tested-by: Zhu Yujie <libriunc@gmail.com>
Tested-by: Chuanhong Guo gch981213@gmail.com
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
[ improve commit description ]
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh kernel configuration of the sf21 subtarget for use with Linux 6.12.
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This change replaces the term 'master' with 'controller' in the
Siflower SPI driver (sf_qspi) to align with the Linux kernel's
inclusive language policy.
Tested-by: Jingkun Zheng <mx@kevinmx.top>
Tested-by: Zhu Yujie <libriunc@gmail.com>
Tested-by: Chuanhong Guo gch981213@gmail.com
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This involves rebasing the patches and resolving any conflicts
arising from changes in the base kernel between the previous
supported version and 6.12.
Tested-by: Jingkun Zheng <mx@kevinmx.top>
Tested-by: Zhu Yujie <libriunc@gmail.com>
Tested-by: Chuanhong Guo gch981213@gmail.com
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop patches from the 6.12 patchset that have been merged into the
mainline Linux kernel since the previous version.
Dropped patches:
001-net-phy-c45-add-genphy_c45_pma_read_ext_abilities-fu.patch
002-net-phy-Optimize-phy-speed-mask-to-be-compatible-to-.patch
003-net-phy-Add-driver-for-Motorcomm-yt8821-2.5G-etherne.patch
014-riscv-add-an-option-for-efficient-unaligned-access.patch
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Zhu Yujie <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20555
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Most users on forums face a broken 802.11r setup when having
a very simple 802.11r config (i.e., just ieee80211r enabled).
In most cases, simply bumping reassociation_deadline to
20000 fixes their problems and allows 802.11r to just work.
Reassociation Deadline is already set to 20 seconds on Cisco
equipment by default[1] which is why this value has been
chosen.
It is also mentioned on the OpenWRT Wiki as a value that should
be changed in order for 802.11r to work on Apple devices. I think
it would be better to change the defaults instead so users don't
have to do much work for a working setup.
[1]: https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/80211r-ft/b-80211r-dg.html
Fixes: https://github.com/openwrt/openwrt/issues/7907
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is useful to alter the default ban time after an STA
association is rejected for being below RSSI threshold.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20811
Signed-off-by: Robert Marko <robimarko@gmail.com>
APK will generate the compressed scripts.tar by default, however we rely
on using TAR support for updating the tarball on the fly and this does not
work when tarball is compressed and will cause the following errors:
staging_dir/host/bin/tar: Cannot update compressed archives
Try /staging_dir/host/bin/tar --help' or
staging_dir/host/bin/tar --usage' for more information.
So, lets simply decompress the scripts.tar.gz before usage and then
compress it after we are done.
Fixes: 5d85657f6d ("apk-tools: implement compression of on-device scripts.tar")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Airoha AN7581 SoC supports a Network Processor (NPU) to offload WiFi
traffic. Add the required bits to enable the support of it in the MT76
driver. This will be enabled by default if we are compiling for the
Airoha AN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ improve commit title/description ]
Link: https://github.com/openwrt/openwrt/pull/20826
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch to .remove_new for downstream driver that still use the old
.remove to reduce patch delta for 6.12 bump.
Suggested-by: Zhu Yujie <libriunc@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds the -Wl,-z,pack-relative-relocs linking options.
This reduces the size of some binaries.
This is only supported on i386, x86_64, aarch64 and loongarch64 in
binutils. This feature is not support for MIPS.
musl libc supports it since version 1.2.4 .
glibc supports it since vesion 2.36.
binutils ld supports it since version 2.38 for x86 and since version
2.43 for LoongArch.
This reduces the size of the armsr default root file system from
5,262,198 bytes to 5,200,950 bytes by 61,248 bytes.
Link: https://github.com/openwrt/openwrt/pull/20679
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
