Add compatibility with the new fortify-headers 2.3.3 by
disabling two warnings.
Fixes: 6268692bd2 ("toolchain: fortify-headers: Update to version 2.3.3")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20552
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 4e68103c4e ("uboot-rockchip: fix build with swig 4.3.0")
Link: https://github.com/openwrt/openwrt/pull/20538
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With this change, the interface identifier can be configured via LuCI.
Signed-off-by: Peter Meiser <peter.meiser@gmx.com>
Link: https://github.com/openwrt/openwrt/pull/19318
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add pending patch that disable libmagic support as this cause
reproducibility issue due to timing of presence of libmagic library at
times e2fsprogs gets compiled.
The new patch adds control on libmagic inclusion and we add the
--without-libmagic to the configure args by default.
Reported-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant patch for host build as this has been fixed in 1.44.1
but for some reason it wasn't notice with the patch directly refreshed
(with the fix right up)
Fixes: 198172c048 ("package/utils/e2fsprogs: update to 1.44.1")
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
0d0fac30075f dhcpv4: bump problem scenario up to warn
bf6137092346 config: properly set log level from uci
7956f4271b4e dhcpv6: RFC4833 timezones
7000557cd8f6 dhcpv6-ia: respect prefix assigned to interface (>= /64)
e1e60601ffeb odhcpd: improve odhcpd_urandom()
c2eb4b59f107 config: fix erroneous clamp message if clamp value == max
54b9e729b00d dhcpv4: bail earlier on release/decline
417f4b11d352 dhcpv4: don't hardcode options array length
d63fa3c3612c dhcpv4: shrink struct dhcpv4_message
9653b43617e3 dhcpv4: use iovec for forcereconf messages, fix hash
bf41f4edfbe3 dhcpv4: fix padding of iovec message in dhcpv4_handle_msg()
be68f423c528 dhcpv4: some minor cleanups post-iovec
e24a371ef714 dhcpv4: use iovec for forcerenew opts
bd353e891ae6 dhcpv4: use iovec for router and DNS server
b81cfaa7859e dhcpv4: use iovec for DNS search and MTU
578a9289440b dhcpv4: use iovec for netmask/hostname/broadcast
5bafc17b79d8 dhcpv4: use iovec for leasetime/renew/rebind
b63448ffe447 dhcpv4: introduce a reply_opts array
0533eaea0a94 dhcpv4: use iovec for DNR
6329e37d595d dhcpv4: use iovec for NTP
87fee619205d dhcpv4: use iovec for message and serverid
2f97bf0b56de dhcpv4: reorder some more variables in dhcpv4_handle_msg()
18c1b02bdc20 dhcpv4: remove one more variable from dhcpv4_handle_msg()
6fd691ff29cd dhcpv4: move dest handling from dhcpv4_handle_msg()
1f803caf9a1f dhcpv4: don't copy reqopts around
b1be3984ebf8 dhcpv4: more refactoring of dhcpv4_handle_msg()
85717bedf8ce dhcpv4: clarify variable names in dhcpv4_handle_msg()
be864ccf9919 dhcpv4: some more cleanups to dhcpv4_handle_msg()
f87464520564 dhcpv4: preparations for iovec usage
f48e1c205af3 odhcdp: use a more suitable clock
7e78caac4eae dhcpv6: change dhcpv6 message type check in relay
288abd9c4046 dhcpv6: move dhcpv6 message type check for early exit
d504458ef515 odhcpd: add a simple build script
4ee309a54011 github: improve CI
ff3a241ccc98 odhcpd: shrink binary size by creating a logging function
e2ecf7ba6d72 odhcpd: support stderr logging
5de3b0d5b509 odhcpd: add log helpers
398d03a1a236 config: cap dhcpv6_pd_min_len to max instead of only logging error
4f54738d3ae7 config: clamp dhcpv6_hostid_len instead of only logging an error
465f19c9c2e3 config: clamp ra_mtu into 1280-65535 range
434b06133997 config: cap ra_retranstime and warn instead of only logging an error
e5f58a90a147 config: cap ra_hoplimit to maximum and warn instead of logging an error
208eb10307c1 config: cap ra_reachabletime to RFC maximum instead of logging error
93449f1513b4 config: drop double size lease times; they are all UINT32_MAX;
439c0ceab131 router: redefine ra_mininterval and ra_maxinterval as uint32_t
84b4dfe81363 config: clamp ra_mininterval, ra_maxinterval, ra_lifetime at load time
aa4f26232e05 router: refactor calc_ra_lifetime; redefine ra_lifetime as uint32_t
6ece28ffd475 config: do MaxRtrAdvInterval init at (ra_maxinterval) init time
dc03e02d973e router: Apply updated values from RFC9096 (updates RFC4861) to RA/ND
cc7766c12abe router: Apply updated values from RFC8319 (updates RFC4861) to RA/ND
964da13e758c config: refactor parse_leasetime() - branch amount remains same
9646c749467b github: fix CMAKE_SYSTEM_PROCESSOR copy&paste
288206c9a2ed github: add CI build
30780debd691 odhcpd: fix a compilation error
e0b2c3cf9476 odhcpd: allow assignments to be reassigned
01e5e311b0db odhcpd: support multiple per-client DUIDs
aebc647a6b7b odhcpd: support assignments on the basis of IAID
cc3ec9c20c61 odhcpd: support IAIDs for static DHCPv6 leases
e42c62725942 odhcpd: break up complex matching logic
e1123906a4bc odhcpd: document the ubus interface
c69200195263 dhcpv4: generate dbus events on lease expiry
dd7a2d474d0d dhcpv4: fix ubus events
22481d848e0d odhcpd: remove mac_len argument to ubus_bcast_dhcp_event()
d31d64efd56c odhcpd: fix ubus support flag in help msg
9bc1b4e26e10 odhcpd: reduce use of WITH_UBUS defines in code
d402cdae4316 ndp: fix macOS IPv6 compatibility by using link-local source addresses
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
77e1ae21e67f odhcp6c: set server address from Information-request reply
e24ac1cf8c27 dhcpv6: use a per-interface IAID for IA_NA requests
053e6c4b3863 github: improve CI
b65ff293a969 dhcpv6: Check status code for IA_ADDR operations
3c7e425169e1 dhcpv6: Add error checking to handle renew failure for IA_PD operations
8de25373a860 dhcpv6: dhcpv6_parse_ia refactor to switch case
ca3cd525f447 odhcp6c: fix deamon raw buffer inc
d7afeea2b965 dhcpv6c: fix illegal DHCPV6_OPT_FQDN
70f7467db301 script: don't ignore RA with zero router lifetime
6ca1552cb3fe odhcp6c: sync and accumulate RA & DHCPv6 events as fast as possible
29b58cfb4711 odhcp6c: update cmake file
ee6d4a82bbeb github: add CI build
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add IPQ Wifi entry for ath79 TP-Link Archer C60 v2.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
Whenever the first bss is removed, any pending scan still keeps a reference
to it. Cancel it in order to prevent use-after-free bugs.
Reported-by: Chad Monroe <chad.monroe@adtran.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
df2f5c9a30f8 veth: delete device before creation to handle stale state
b6d371f30770 system-linux: handle RTM_DELLINK events for device state tracking
777f5942fa7d system-linux: only parse device status for AF_UNSPEC link messages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove earlyprintk from bootargs for arm64 boards.
This option is only valid for arm:
```
Unknown kernel command line parameters "earlyprintk",
will be passed to user space.
```
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Export WiFi 6E (HE) and WiFi 7 (EHT) operation data in scan results.
These additional data can be useful to check wifi channel utilization
by nearby stations.
Example:
Cell 32 - Address: xx:xx:xx:xx:xx:xx
Mode: Master Frequency: 6.115 GHz Band: 6 GHz Channel: 33
Signal: -14 dBm Quality: 70/70
Encryption: SAE (CCMP)
HE Operation:
Center Frequency 1: 39
Center Frequency 2: 47
Channel Width: 160 MHz
EHT Operation:
Center Frequency 1: 47
Center Frequency 2: 63
Channel Width: 320 MHz
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19208
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes the following commits from upstream Linux between 6.16 and 6.16.12:
wifi: ath11k: clear initialized flag for deinit-ed srng lists
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
wifi: ath11k: fix dest ring-buffer corruption
wifi: ath11k: fix source ring-buffer corruption
wifi: ath11k: fix dest ring-buffer corruption when ring is full
wifi: ath11k: fix group data packet drops during rekey [1]
wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
[1] The patch "940-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch" has been removed, as it has been fixed upstream in "wifi: ath11k: fix group data packet drops during rekey" and is added in 945 patch.
Related: https://github.com/openwrt/openwrt/pull/18705
Related: https://github.com/openwrt/openwrt/issues/9555
Related: https://github.com/openwrt/openwrt/issues/14117
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove leading 0 from filename.
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Link: https://github.com/openwrt/openwrt/pull/20395
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
odhcp6c already supports custom DUIDS on a per-interface basis. When no client
identifier has been set, odhcp6c will generate one on the basis of the MAC
address of the given interface.
This is contrary to how DUIDs are meant to be used, as the client identifier
will vary from interface to interface, while it is meant to remain stable for a
given host, no matter how the network hardware changes (see RFC8415, §11).
Fix this by letting odhcp6c use the global DHCP DUID, if configured.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
This makes the DHCPv4 client use the global DHCP DUID to generate a
RFC4361-style client identifier.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
odhcp6c and odhcpd currently generate custom DUIDS on a per-interface basis
using the MAC address of the given interface.
This is contrary to how DUIDs are meant to be used, as the client identifier
will vary from interface to interface, while it is meant to remain stable for a
given host, no matter how the network hardware changes (see RFC8415, §11).
The same problem exists in odhcpd, which also generates server-side DUIDs on a
per-interface basis.
In order to support a stable per-device DUID, generate one on first boot and
store it via uci.
Currently, a DUID-UUID style clientid is generated. This is mostly meant as an
RFC, and we might consider using a different kind of DUID instead (DUID-LLT,
DUID-EN).
One drawback is that this will typically change the DUID used on existing
OpenWrt devices when upgrading to a new release. However, that seems
unavoidable and is a one-time pain in order to have stable DUIDs (and in many
cases, it shouldn't cause any issues).
v2: move the uci cfg generation outside of an IPv6-only block since this
is relevant to the DHCPv4 client as well
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20359
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix package name and AUTOLOAD parameter to match the
actual kernel module name (leds-group-multicolor), enabling proper
auto-loading at boot.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20447
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also implemented the med fast-start -> lldp fast-start change.
lldpd includes a backwards compat handler for the older med command,
but it's better to make these changes so they align with documentation.
Changes:
https://github.com/lldpd/lldpd/releases/tag/1.0.20
Changes:
Enable fast start unconditionally (and move its configuration in "configure lldp")
Make VLAN advertisements configurable
Fix:
Do not break zero-copy traffic on Linux
Fix crash on rapid addition/removal of interfaces
Fix management address selection when pattern is a negative IP address
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20438
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR30H. The MR30H is a POE
powered 802.11ac access point with an integrated 5 port Gigabit switch.
MR30H hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac, QCA9889 802.11/b/g/n/ac scanning radio
* Serial: Internal header (J8, 2.54mm, populated)
LAN5 (rear) is for POE input. LAN4 has POE output (802.3af) when powered
by an 802.3at source.
The LAN4 port is used for tftp booting in U-Boot.
This device does not have secure boot, but cannot be flashed without
external programmers (TSOP48 NAND) as Meraki disabled interrupting U-Boot
for any device that updated after ~2017.
Disassembly:
* Remove the two T10 screws on the rear of the AP.
* Using a guitar pick or similar plastic tool, insert it on the side between
the grey metal plate and the white plastic body and pry up gently.
* The rubberised border on the metal plate does not need to be removed.
* The metal back plate has several latches around the perimeter (but none on
the bottom by the Ethernet ports).
* Once you have removed the metal back plate, push up gently on the bottom
Ethernet ports while pulling gently on the rear-mounted Ethernet port to remove
the PCB.
* The PCB should come free from the plastic housing, pull the bottom
(4 Ethernet ports) up as if you are opening a book.
* If done carefully, there is no need to remove the WiFi antenna connectors
to access the NAND flash.
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
opposite side of the PCB.
* To flash, you need to desolder the TSOP48 or use a 360 clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr30h
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Resolder the NAND after overwriting the `u-boot` regions.
OpenWrt Installation:
* After flashing NAND with the external programmer. Plug an Ethernet
cable into port 4. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Alternative installation steps if your device has U-Boot older than:
`U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700)`
**BIG FAT WARNING BEGIN**
Attmping to interrupt boot on a newer U-Boot release may permanently
brick your device! See: riptidewave93/LEDE-MR33#13
**BIG FAT WARNING END**
* Use `ubootwrite.py` from the above GitHub repository to transfer the
`u-boot.itb`
image to the router.
```
./ubootwrite.py --serial=/dev/ttyUSB0 --write u-boot.itb
```
* To avoid bricking your router, it is highly recommended at this point that
you flash the unlocked U-Boot to the `part.safe` ubi volume.
```
run set_ubi && ubi write $loadaddr part.safe 0x2fd48
```
* Power cycle the router. The stock Meraki U-Boot will boot `part.safe` which
is now the unlocked U-Boot.
* Use the new U-Boot build (`" "` to interrupt boot) to
`tftpboot` the OpenWrt initramfs image:
```
dhcp
setenv serverip <tftp_server_addr>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
bootm
```
* It is only recommended to flash U-Boot to the `u-boot` NAND region from
Linux:
```
insmod mtd-rw i_want_a_brick=1
```
* Copy `u-boot.elf` to the router:
```
scp -O u-boot.elf root@192.168.1.1:/tmp/
```
Note: If any of the below commands fails, YOU WILL HAVE A BRICK IF YOU
REBOOT OR LOSE POWER. Only a hardware programmer can recover the device.
```
flash_erase /dev/mtd8 0 0
nandwrite -p /dev/mtd8 /tmp/u-boot.elf
```
Note: ONLY use `u-boot.elf` when flashing the `u-boot` region (`/dev/mtd8`);
`u-boot.bin` or `u-boot.itb` will BRICK YOUR DEVICE
* `scp` the `sysupgrade` image to the device and run the normal `sysupgrade`
procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Z3. The Z3 is a "teleworker"
device with 802.11ac and an integrated 5 port Gigabit switch.
Z3 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x24`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_z3-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubimkvol /dev/ubi0 -N ART -s 524288
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
When lots of events are waiting to be received, the default buffer size
is not enough, and hostapd can run into "No buffer space available" on
recvmsg. This will cause the netdev state tracking to go out of sync.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Previously, devices would have to select `CONFIG_RTL8261N_PHY=Y` in the
whole target's kernel config. Now that this driver is becoming usable
for devices other than Realtek switches, allow packaging this driver
separately.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/20429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the copy_from_user() and copy_to_user() functions for accessing
memory provided by the user in the ptm netdev iotls.
In addition also check for root permission before executing ioctl.
Suggested-by: Stanislav Fort from Aisle Research
Reported-by: Stanislav Fort from Aisle Research
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b462895d3157 lua: CMakeLists: drop redundant cmake_minimum_required
f247c18f8a55 examples: CMakeLists: drop redundant cmake_minimum_required
83a70399030d github: add CI build
d31effb4277b ubusd: Fix out of bounds access in event register message
d95837b1b143 ubusd: acl: compare uid/gid instead of user/group strings
b81257bb20dd ubusd: load extra group IDs for a client process
7d7b45fea05b add debian/ directory
aa4a7ee1d341 ubusd: fix more instances of missing length checks for patterns
60e04048a0e2 ubusd: fix ACL check for receiving events
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Realtek RTL8822CS support to the rtw88 package.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20423
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add IPQ Wifi entry for ath79 TP-Link Archer C59 v1.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix trivial compilation warning caused by downstream full print patch.
../src/app_list.c: In function 'print_full':
../src/app_list.c:85:35: warning: format '%zu' expects argument of type 'size_t', but argument 2 has type 'uint64_t' {aka 'long long unsigned int'} [-Wformat=]
85 | printf("Installed-Size: %zu\n", pkg->installed_size);
| ~~^ ~~~~~~~~~~~~~~~~~~~
| | |
| | uint64_t {aka long long unsigned int}
| unsigned int
| %llu
../src/app_list.c:86:25: warning: format '%zu' expects argument of type 'size_t', but argument 2 has type 'uint64_t' {aka 'long long unsigned int'} [-Wformat=]
86 | printf("Size: %zu\n", pkg->size);
| ~~^ ~~~~~~~~~
| | |
| | uint64_t {aka long long unsigned int}
| unsigned int
| %llu
../src/app_list.c:58:31: warning: unused variable 'd' [-Wunused-variable]
58 | struct apk_dependency d;
Remove unused variable and use PRIu64 to handle uint64_t type.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
