The new SerDes mdio driver produces the following compilation
error in non-debug builds.
drivers/net/mdio/mdio-realtek-otto-serdes.c:72:12:
error: 'rtsds_sds_to_mmd' defined but not used [-Werror=unused-function]
72 | static int rtsds_sds_to_mmd(int sds_page, int sds_regnum)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Move the function into the debug section.
Fixes: 7a7ee72c4d ("realtek: mdio: add SerDes driver")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20078
Signed-off-by: Robert Marko <robimarko@gmail.com>
In first commit I successfully bring WAN port into ethernet switch,
without realizing that I was using custom bootloader. But if using
original bootloader it do not works. WAN port in original bootloader
is tied to using its own GMAC.
This fix is made so this firmware will be compatible with orignal
bootloader, so the user can directly flash from stock firmware without
changing anything.
Signed-off-by: Roy H <roy@altbytes.com>
Link: https://github.com/openwrt/openwrt/pull/20039
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Despite having the same tplink.dtsi file, there are differences in wifi
Move wifi nodes out of dtsi to make it clear what the chipset is and
what calibration size should be used.
While at it, change to use led-sources to simplify LED setup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20024
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now the SerDes access is realized with some helper functions
in the mdio bus. These were moved around a lot and had no real home.
End that temporary solution to move them where they belong.
The target design for the different Realtek drivers is as follows:
- dsa driver manages switch
- pcs driver manages SerDes on high level (to be developed)
- mdio driver manages SerDes on low level (this commit)
This driver adds the low level SerDes access via mdio. For debugging
purposes the user can interact with the SerDes in different ways.
First, there is a debug interface in
/sys/kernel/debug/realtek_otto_serdes/serdes.X/registers.
With that a dump of all registers can be shown.
> cat /sys/kernel/debug/realtek_otto_serdes/serdes.4/registers
Back SDS 4: 00 01 02 03 04 05 06 07 08
SDS : 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248
SDS_EXT : 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA
...
Second, one can read/write registers via the mmd functions of the
mdio command line tool. Important to know: The registers are accessed
on the vendor specific MDIO_MMD_VEND1 device address (=30). Additionally
the SerDes page and register are concatenated into the the mmd register.
Top 8 bits are SerDes page and bottom 8 bits are SerDEs register.
E.g.
- mmd 0x0206 : SerDes page 0x02, SerDes register 0x06
- mmd 0x041f : SerDes page 0x04, SerDes register 0x1f
Read register 0x02 on page 0x03 of SerDes 0
> mdio realtek-serdes-mdio mmd 0:30 raw 0x0302
Write register 0x12 on page 0x02 of SerDes 1
> mdio realtek-serdes-mdio mmd 1:30 raw 0x0212 0x2222
For now this driver is only defined in the devicetree and activated
in the kernel build. There is no current consumer but at least
the debugging interface is available. Cleanup of the currently used
SerDes functions will come later.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20062
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is some open coding in the ethernet driver. Drop
that and use kernel helpers instead.
- Use napi_gro_receive() instead of local skb list
- Use skb_put_data() instead of skb_put() plus memcpy()
- Use netdev_alloc_skb_ip_align() instead of manual alignment
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable kernel 6.12 as the testing kernel for airoha.
This first commit will largely maintain feature-parity with kernel 6.6.
DTS changes are backwards-compatible with kernel 6.6.
Tested to flash and boot on Gemtek W1700K (#17869).
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/19038
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh patch which was accidentally without non-confrming style and
not matching line numbers.
Also add patch description by copying the description of the commit
in OpenWrt, so the patch can be applied using `git am` and is ready
for upstream submission.
Fixes: afcec128c5 ("mediatek: add support for trng on mt7988a")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use upstreamed patches for adding IPQ CMN PLL driver support and its
node and clocks to the DTS accordingly.
In addition, set clock-div and clock-mult properties instead of the
frequency itself for the XO board clock in all board files as it's
converted to a fixed factor clock.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19890
Signed-off-by: Robert Marko <robimarko@gmail.com>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This addresses #9113 by adding up to 1MB padding after writing the
rootfs image. On boot mount_root will probe for existing filesystems
after the rootfs image data. Without overwriting the initial free
space left on the rootfs partition, OpenWrt might incorrectly detect
an exising filesystem and fails to mount it, resulting in a bricked
device as the overlayfs will not be mountend and settings will not be
available.
Fixes#9113.
Signed-off-by: Orne Brocaar <info@brocaar.com>
Link: https://github.com/openwrt/openwrt/pull/19997
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add driver for hardware random number generator found in MT7981, MT7988
and MT7987. This gives us a fast source of high-quality random numbers
on those platforms.
root@OpenWrt:~# cat /dev/hwrng | rngtest -c 10000
rngtest 6.17
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
rngtest: starting FIPS tests...
rngtest: bits received from input: 200000032
rngtest: FIPS 140-2 successes: 9988
rngtest: FIPS 140-2 failures: 12
rngtest: FIPS 140-2(2001-10-10) Monobit: 2
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 4
rngtest: FIPS 140-2(2001-10-10) Long run: 6
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=616.108; avg=11979.007; max=19531250.000)Kibits/s
rngtest: FIPS tests speed: (min=1.859; avg=82.116; max=83.656)Mibits/s
rngtest: Program run time: 18629928 microseconds
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The kernel config accidentally contains CONFIG_UBIFS_FS_AUTHENTICATION
which select a number of other unnecessary components, remove them.
The target has at least two subtargets, only one is currently
implemented. Move the Device builds into a file for this subtarget.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20027
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The only consumers of the Realtek HSGMII (2.5G SGMII) mode were
the RTL8226/RTL8221B PHYs. These have been converted to dynamic
SGMII/2500base-x mode switching. Drop the leftovers of the mode
implementation.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20002
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio controller got its own dts node with a dedicated bus node.
Until now it still searches the phy nodes in the ethernet node.
Change the driver so it searches the nodes at the right location.
For this to work move the phy nodes in all dts/dtsi over to the new
bus node. Use the following replacement rule:
Replace old full declaration
ðernet0 {
mdio-bus {
...
};
};
and old abbreviated declaration
&mdio {
...
};
simply with the new declaration
&mdio_bus0 {
...
};
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19986
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Until now the mdio bus is a subnode of the ethernet device. This
coupling is different from upstream and wrong. Ethernet and mdio
are different devices. Additionally differentiate between mdio
controller and mdio bus. To make it clear:
- There is one mdio controller
- With up to 4 busses (on RTL93xx)
Prepare new mdio controller and bus nodes with SoC specific compatibles.
These will be used later when refactoring the mdio driver probing.
Remark! For now only define the first bus for the RTL93xx targets.
So the driver still relies on "rtl9300,smi-address = <x y>;". It will
need much more refactoring to get totally aligned with upstream.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19986
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While converting the RTL931x SerDes code to the new frontend
access methods, the target specific workarounds where left in
place. The old functions were kept and the phy/sds mapping
was unchanged too. It is time to clean this up
- drop the old functions
- reuse the existing read/write logic
- harden the new functions
For now keep the function naming rtmdio_...__new() as is. This
will be changed in a future commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19973
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The TP-Link Archer VR1200v (v2) is a low end DSL modem based on the
EcoNet EN751221 processor platform.
While it does have an unlocked bootloader, the factory upgrade feature
requires a cryptographic signature so flashing from the web UI is not
feasible.
The Archer VR1200v (v2) uses a dual-image layout. I have chosen to reuse
this to support dual-boot between OpenWRT and the factory firmware.
Flashing instructions (from bootloader):
Build and then locate the squashfs-sysupgrade.bin image file
Get the length of that file in hex: printf '%X\n' "$(stat -c%s the-file-squashfs-sysupgrade.bin)"
Connect to device with xmodem capability, e.g. picocom --send-cmd lsx -vv -b 115200 /dev/ttyUSB0
Switch device on and press a key within 3 seconds, you should get to a `bldr>` prompt
Type: xmdm 80020000 <file length hex>
Quickly start xmodem and send the file, in picocom that is ctrl+a ctrl+s <paste-the-file-name> enter If the transfer fails to start, wait 30 seconds to a minute for the bootloader prompt to return and then try the command again.
Once the transfer has completed successfully, type the following flash 80000 80020000 <file length hex>
Type `re` or simply restart the device to boot into OpenWRT
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SmartFiber XP8421-B is a fiber modem which is available for $20 online
and has 512MB of memory, 256MB of SPI NAND flash and 2 USB 2.0 ports in
addition to ethernet, wifi and XPON.
Because EcoNet is not currently producing evaluation boards, the XP8421-B
stands in as a convenient, low cost, off-the-shelf, representitive example
of the capabilities of the EN751221 econet processor. This is also the
example board that is included in the upstream Linux patchset.
The XP8421-B, and apparently many other devices of this platform, use a
dual-image layout. I have chosen to reuse this to support dual-boot between
OpenWRT and the factory firmware. Certain design decisions were made with
the goal of not overwriting data that is used by the factory OS.
This commit also introduces a utility for switching between OS_A and OS_B
which are used for OpenWRT and Factory OS respectively.
Flashing instructions (from bootloader):
Build and then locate the squashfs-tclinux.trx image file
Get the length of that file in hex: printf '%X\n' "$(stat -c%s the-file-squashfs-tclinux.trx)"
Connect to device with xmodem capability, e.g. picocom --send-cmd lsx -vv -b 115200 /dev/ttyUSB0
Switch device on and press a key within 3 seconds
Enter bootloader username and password: telecomadmin nE7jA%5m
Type: xmdm 80020000 <file length hex>
Quickly start xmodem and send the file, in picocom that is ctrl+a ctrl+s <paste-the-file-name> enter If the transfer fails to start, wait 30 seconds to a
minute for the bootloader prompt to return and then try the command again.
Once the transfer has completed successfully, type the following flash 80000 80020000 <file length hex>
Type go or simply restart the device to boot into OpenWRT
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
