Due to confusing Documentation, the SPI and SLIC base clock and
register location for Airoha AN7583 SoC were wrong.
Fix them with new updated Documentation source to provide correct
clock support.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reuse Device/FitImage recipe instead of open coding it and
drop duplicate KERNEL_INITRAMFS recipe for eDPU.
While at it, lets clean up the boot script to drop uneeded console
setting, earlycon etc.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Move the Device/FitImage recipe to the generic image Makefile to avoid
duplicating it for other subtargets.
Will be used for uDPU/eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This allows to drop a family condition check and in the future
allows to merge nowadays splitted functions. While we are here
replace a hardcoded 0xc value with the new value for better
readability.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
During transmit the driver must adapt the packet length. The
hardware requires at least a memory space of ETH_ZLEN bytes
data plus four bytes for layer 2 FCS. This was calculated
(somehow) but skb->len never got updated and for the minimum
length a RTL838x specific workaround was in place. Clean up
the code and use skb_put_padto() so the length change gets
reflected in skb->len.
While we are here drop zeroing DSA tag because it will be
overwritten by hardware for FCS.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch from auto-scan PHY discovery to explicit DT-based registration
using fwnode_mdiobus_register_phy(). This is the standard approach used
by of_mdiobus_register() and most MDIO drivers.
Auto-scan (phy_mask-based) registration does not attach DT fwnode data
to PHY devices, which means DT properties like "pses" are never parsed.
As a result, PSE controllers referenced from PHY nodes are not linked,
and ethtool PSE commands (--show-pse, --set-pse) do not work.
Store the device_node for each PHY found during DT parsing, suppress
auto-scan by setting phy_mask to ~0, and register each PHY explicitly
after devm_mdiobus_register(). This allows fwnode_find_pse_control() to
resolve PSE references and also establishes proper fw_devlink supplier
relationships.
Additionally this fixes a bug where the RTL8221B is limited to
1G and below due to missing DTS references.
Fixes: 4e00306 ("realtek: mdio: use bus auto registration")
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Link: https://github.com/openwrt/openwrt/pull/22019
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR70/Go GR60.
The Meraki MR70 is a Cisco 802.11ac/WiFi 5 outdoor AP with 1 Ethernet port.
It can be powered by a 12V DC barrel jack (5.5x2.5mm, center positive)
or via 802.3af POE.
The Meraki Go GR60 (codename: Dungbeetle Omni) is identical to the MR70
(codename: Toe Biter Omni), so this document will refer to both devices
as the MR70.
MR70 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (TSOP48 NAND, 3.3V)
* Networking: 1 Gigabit Ethernet
* WiFi: QCA4019 802.11b/g/n/ac
* Serial: Internal header (J10, 2.54mm, unpopulated)
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEPROM)!
Disassembly:
Note: This is an outdoor device that is ultrasonically welded and glued
to weather seal it. Disassembly will compromise the weather seal!
Start by removing the product label on the rear metal mounting plate.
There are four Torx T8 screws under the sticker, remove the screws and
the mounting plate. Remove the two Philips screws under the plate.
Using a chisel (or razor blade) and hammer, cut around the circumfrence
of the device. You need to cut through approximately 2mm of
ultrasonically welded plastic.
After cutting through the plastic, heat the device using a hair drier
(or similar) to soften the glue. A heatgun is NOT recommended as
it will damage the plastic. It is only required to heat the device until
warm (~40C-50C).
Using a plastic pry tool, insert it along the cut you made around
the edge and gently separate. Insert a guitar pick into the opening
while gently lifting the front to cut the glue. The device is glued around
the entire circumfrence.
Once you have removed the plastic front, remove the 4 Philips screws
holding down the main PCB. Release the two WiFi antennas by gently
bending the antenna PCBs to the middle of the unit and pulling up.
Lift the top of the PCB gently while pushing the Ethernet port into the
housing to release it. Turn the PCB over and remove the three Philips
screws holding the metal heat spreader.
The TSOP48 NAND flash (U9, S34ML01G200 or W29N01HV) is located
under the metal heat spreader.
To flash, you need to desolder the TSOP48 or use a 360 clip.
You also need to reprogram the I2C EEPROM (U20, Atmel 24c64). It is not
necessary to desolder the I2C EEPROM, a ch341a USB programmer and SOP-8
clip are inexpensive (~$10) and work well.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr70_gr60
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000-0x7fe0000` (length `0x7380000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x2d` or `0x26`). Remember to re-write the EEPROM with the
modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug in an
Ethernet cable and power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr70-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr70-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr70-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22050
Signed-off-by: Robert Marko <robimarko@gmail.com>
Underdog devices lack a red LED, use the blue LED for
failsafe mode.
Move all config except device name to underdog.dtsi, as
all known underdog devices (MR20/GR10, MR70/GR60) have identical
device tree.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22050
Signed-off-by: Robert Marko <robimarko@gmail.com>
The sgmiisys0 override uses
/delete-node/ mediatek,pnswap;
but mediatek,pnswap is a property, not a child node. The correct
directive would be /delete-property/. As a result, this statement never
had any effect and the property was never removed.
Drop the incorrect override.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22046
Signed-off-by: Robert Marko <robimarko@gmail.com>
NVMEM in UBI support has been present for a while. Use it to get the
MACs. Seems caldata needs to continue to be obtained through userspace.
This fixes label-mac-device as it needs a mac-address nvmem cell.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17068
Signed-off-by: Robert Marko <robimarko@gmail.com>
Follow the recent change where all DTS files were moved to a dedicated dir.
Fixes: 3a39f682df ("qualcommax: ipq50xx: add support for CMCC MR3000D-CI")
Signed-off-by: Robert Marko <robimarko@gmail.com>
CMCC MR3000D-CI is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5000.
Device specification
--------------------
- SoC : Qualcomm IPQ5018
- RAM : 512 MiB DDR3L
- Flash : 128 MiB SPI-NAND (GigaDevice GD5F1GQ5REYIG)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 4x 10/100/1000 Mbps
- Switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 2x LEDs, 2x Buttons
- UART : Through-hole on PCB
- Voltage : 3.3 V
- Assignment : Silkscreened on PCB
- Settings : 115200n8
- Power : 12 VDC, 1.5 A
Installation
-----------------
1. Telnet method
a. Enable telnet
Log in to http://192.168.10.1/ with the password on the sticker
Modify URL according to example (keep your unique hash after ";stok=")
and press Enter:
http://192.168.10.1/cgi-bin/luci/;stok=78becad1b1490e45be2776025cde2b7d/api/NPCnetwork/ping?url=$(telnetd)
You should get the following in the browser:
{"link":0}
b. Run tftp server on IP 192.168.10.254 and put factory image
'openwrt-qualcommax-ipq50xx-cmcc_mr3000d-ci-squashfs-factory.ubi'
in the tftp root dir.
c. Login to 192.168.10.1 with telnet (user: root, pass: from the
sticker).
d. Download factory image from the tftp:
tftp -l factory.ubi -r openwrt-qualcommax-ipq50xx-cmcc_mr3000d-ci-squashfs-factory.ubi -g 192.168.10.254
e. Flash factory image:
export rootfs=$(cat /proc/mtd | grep rootfs | grep -v _ | cut -d: -f1)
ubidetach -f -p /dev/${rootfs}
ubiformat /dev/${rootfs} -y -f /tmp/factory.ubi
f. Reboot:
reboot
2. U-Boot Method using UBI Image (using UART)
a. Place the factory.ubi file on your TFTP server, enter U-Boot CLI
and exec these commands:
tftpboot <your_tftp_server_ip>:factory.ubi
flash rootfs
reset
3. U-Boot Method using initramfs Image (using UART)
a. Place the openwrt-*-initramfs-fit-uImage.itb file on your TFTP
server and rename it to initramfs.bin
b. Enable serial console, enter to U-Boot CLI and exec these commands:
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
c. Once boot completed, upload the sysupgrade.bin file to router's
/tmp directory (using scp or wget) and execute the following command
in openwrt shell:
sysupgrade -n /tmp/sysupgrade.bin
MAC Addresses
-------------
+--------------+-------------------+-------------+
| Interface | MAC example | Location |
+--------------+-------------------+-------------+
| LAN | 84:7a:xx:xx:xx:dd | 0:ART, 0x6 |
| WAN (label) | 84:7a:xx:xx:xx:dc | 0:ART, 0x0 |
| WLAN 2.4 GHz | 84:7a:xx:xx:xx:de | 0:ART, 0xc |
| WLAN 5 | 84:7a:xx:xx:xx:df | 0:ART, 0x12 |
+--------------+-------------------+-------------+
Notes
-----
1. U-Boot is protected by a password (pass: netpower).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21952
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Teltonika RUT104 3G HSUPA router.
This has been supported since about 20 years in the upstream Linux
kernel after initial contribution by Paulius Zaleckas from Teltonika.
It has some historical significance because I think it was one of the
first Teltonika Linux-based 3G routers.
Installation from scratch is done using the UART:
- UART soldering instructions with picture are available on the
Link: (see bottom of committ message).
- First *diet down* your OpenWrt build as minimal as you can,
I really mean this, delete everything you don't need. There
is not much RAM to go around.
- Extract the "factory" firmare which is essentially just a tar.gz
archive:
tar xvfz openwrt-gemini-generic-teltonika_rut104-squashfs-factory.bin
From the RedBoot menu:
- Do NOT UNDER ANY CIRCUMSTANCE try to use the "upgrade firmare" (Z)
alternative!
- Extract the three files zImage, rd.gz and hddapp.tgz from the archive.
- Put these three files in the root directory of your TFTP server
(usually /var/lib/tftpboot)
- Hit 6 and set up the IP address for your device (e.g. 169.254.1.2 if
you're using local link).
- Hit Y to "Upgrade Kernel", enter TFTP and your hosts IP number and
type zImage. The kernel should upload and flash.
- Hit R to "Upgrade Ramdisk", enter TFTP and your hosts IP number and
type rd.gz. The "ramdisk" (i.e. the second part of the kernel)
should upload and flash.
- Hit A to "Upgrade Application", enter TFTP and your hosts IP number
and type hddapp.tgz. The "application" (i.e. the root filesystem)
should upload and flash.
This has a 1024KB Kernel partition, just extend the existing Make
functions to handle also this. The initramfs is 0x500000 instead
of 0x600000 for this one so add a parameter explicitly parameterizing
the initramfs size.
Mark non-default due to the small RAM and flash on this device.
I currently have no idea how to actually talk to the modem on this
thing but it is probably using the high-speed "modem UART" of the
Gemini. I'd be willing to help whoever wants to experiment with
it.
Link: https://dflund.se/~triad/krad/teltonika/
Link: https://github.com/openwrt/openwrt/pull/22045
Signed-off-by: Linus Walleij <linusw@kernel.org>
The target name of meraki_mx64-a0 in
target/linux/bcm53xx/image/Makefile used not to be consistent with the
one defined in target/linux/bcm53xx/base-files/lib/upgrade/platform.sh
and generates warning for "Image check failed" during sysupgrade.
This commit would also make the target name for meraki_mx64-a0 to
conform to the openwrt standard.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22034
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Linux kernel assumes that the u-boot environment covers the full
partition, but it only covers 0x1000 bytes. Linux checks the CRC and
does this over the full partition. This fails like this:
```
u-boot-env-layout 1f000000.spi:flash@0:partitions:partition@30000:nvmem-layout: Invalid calculated CRC32: 0xfcac8c41 (expected: 0x14e6335a)
u-boot-env-layout 1f000000.spi:flash@0:partitions:partition@30000:nvmem-layout: probe with driver u-boot-env-layout failed with error -22
```
Define the u-boot environment with a length of 0x1000 bytes to calculate
the CRC only over this area.
When replicating the u-boot environment with these parameters it
generates the same CRC:
```
mkenvimage -p 0 -b -s 0x1000 -o output.bin input.txt
```
Fixes: https://github.com/openwrt/openwrt/issues/21696
Fixes: 5e3a602def ("ath79: sitecom,wlrx100: use nvmem")
Link: https://github.com/openwrt/openwrt/pull/22030
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device specific constants belong into the config structure.
No need to initialize them manually during probing within a
family_id switch statement. Although there are lots of constants
that need to be converted start with port_ignore as a simple one.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22026
Signed-off-by: Robert Marko <robimarko@gmail.com>
On RTL930x, RTL931x and even RTL838x the smi topology is
configured very similar. There is a bus mapping (RTL930x
and RTL931x) and a port mapping (all three). Define a
common helper that can take care of this setup and call
it before bus registration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22008
Signed-off-by: Robert Marko <robimarko@gmail.com>
Part of the configuration sequence for 1G operation can be identified as
setting autonegotiation to enabled for that mode. Starting from a previous
commit, this is being handled properly in the set_autoneg implementation.
Thus, remove that part from the sequence which doesn't make sense there
anymore and might just cause problems.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22013
Signed-off-by: Robert Marko <robimarko@gmail.com>
The autonegotiation setting might not have been working for RTL931x the
whole time. While there weren't any reports about issues so far, these
issues might just have been hidden behind other circumstances.
While all other variants of the Otto family have the corresponding
settings in [page 0x2 register 0x0] of a SerDes, RTL931x has a special
Front/Background SerDes architecture and actually moved the
autonegotiation settings to a digital Background SerDes. Since we use a
special mapping to have a consistent view on these Background SerDes,
RTL931x needs to write the settings to another page.
To fix this, adjust the autonegotiation setting for all variants. The
generic implementation is kept but uses per-variant register field
definitions. Those are added for all variants here, with the differing
page for RTL931x.
Another static data definition is renamed since it conflicts with a
change introduced here.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22013
Signed-off-by: Robert Marko <robimarko@gmail.com>
Slight differences between the variants of the Otto family are handled
so far handled using function indirection by defining per-variant
operations which are called from generic implementations. In several
case, this can still be optimized because the variants only differ in
some register addresses and/or bits while the procedure otherwise is
exactly the same.
To address this, add a new SerDes register struct where register fields
can be described and later used by generic implementations which otherwise
would need to be separate just because of slight differences. Add two
register fields for autonegotiation to that register struct which are
used by a successing patch to address a real issue.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22013
Signed-off-by: Robert Marko <robimarko@gmail.com>
Align the ipq40xx target to the pattern already used on other devices where
the device DTS are placed in a dedicated directory separate from the files
directory.
This, while trying to enforce a common pattern for every target, also permits to
do modification to device DTS without having to trigger a recompilation of the
entire kernel (as the files directory is not touched)
Link: https://github.com/openwrt/openwrt/pull/22040
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Align the ipq806x target to the pattern already used on other devices where
the device DTS are placed in a dedicated directory separate from the files
directory.
This, while trying to enforce a common pattern for every target, also permits to
do modification to device DTS without having to trigger a recompilation of the
entire kernel (as the files directory is not touched)
Link: https://github.com/openwrt/openwrt/pull/22039
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Align the qualcommbe target to the pattern already used on other devices where
the device DTS are placed in a dedicated directory separate from the files
directory.
This, while trying to enforce a common pattern for every target, also permits to
do modification to device DTS without having to trigger a recompilation of the
entire kernel (as the files directory is not touched)
Link: https://github.com/openwrt/openwrt/pull/22038
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Align the qualcommax target to the pattern already used on other devices where
the device DTS are placed in a dedicated directory separate from the files
directory.
This, while trying to enforce a common pattern for every target, also permits to
do modification to device DTS without having to trigger a recompilation of the
entire kernel (as the files directory is not touched)
Link: https://github.com/openwrt/openwrt/pull/22037
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove incomplete SPI flash definitions from affected device tree files.
These fragments only defined address-cells and size-cells without any
actual flash configuration (partitions, compatible string, etc.).
After applying openwrt/openwrt#20942 ("kernel: of: fix bad cell count error
for SPI flash node"), the kernel properly handles SPI flash nodes without
requiring these incomplete definitions in device-specific DTS files.
This cleanup eliminates unnecessary code that was likely a workaround for
the previous kernel issue.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22036
Signed-off-by: Robert Marko <robimarko@gmail.com>
We can now setup most of the modes for RTL930x, recently XSGMII, QSGMII
and USXGMII-SX have been added. Thus we don't need a big list of allowed
modes anymore in SerDes setup. Drop this without replacement. Other
modes are still rejected in other places or will be rejected later with
a proper SerDes capability handling.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add everything that's needed to setup QSGMII mode on the 5G SerDes. This
includes patch sequences, additions to symbol error reset and read, and
allowing this mode during SerDes setup.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add everything that's needed to setup USXGMII-SX mode (10G single port
USXGMII). This includes patch sequences and adjustments to the symbol
error reset and reading, and allowing it in the SerDes setup.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For each port (or port group) the mdio bus needs to define the
PHY type that is attached to it. There are the following bit
values that need to be set in SMI_MAC_TYPE_CTRL.
- 0x0: 10G/1G Fiber (SerDes)
- 0x1: 10G/2G5 GPHY
- 0x2: FEPHY
- 0x3: GPHY
SerDes ports are out of scope of the mdio driver and are handled
by the PCS driver. So the corresponding bits are untouched. That
is not good as the register default is 0x3 for ports 0-23. To
make it simple: Without proper setup devices that have SerDes
driven fiber ports at address 0-23 do not poll in the right way.
Link detection is broken.
Fix this by initializing the register to zero. This way all ports
that are not setup by the mdio driver default to "SerDes". That
should be a reasonable assumption.
Fixes: b271735 ("realtek: mdio: Simplify RTL930x phy polling setup")
Reported-by: Joe Holden <jwh@zorins.us>
Suggested-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22032
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices contain a single MAC address in the U-Boot environment.
Set it as eth0 and label MAC in device tree.
To maintain the current state, the 02_network script still sets
individual port MAC addresses and the bridge MAC address.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/22024
Signed-off-by: Robert Marko <robimarko@gmail.com>
FIPS 140-3 recommends that all crypto implementations should be tested
before first use. Testmanager performs initial tests based on existing
test vectors. Not all algorithms have defined test vectors, so to improve
this situation, this commit backports recently added test vectors for
three cipher suites:
* authenc(hmac(md5),cbc(des3_ede)),
* authenc(hmac(sha224),cbc(aes)),
* authenc(hmac(sha384),cbc(aes)).
These vectors were calculated using a software implementation and then
double-checked on Mediatek MT7981 (safexcel) and NXP P2020 (talitos).
Both platforms passed self-tests.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21970
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add PCIe controller and PHY support for EN7528 SoC. This includes
a new PCIe PHY driver, EN7528-specific startup in the MediaTek PCIe
controller, and a fix for bogus prefetch window reads on bridges
that do not implement the registers.
Enable WiFi for the DASAN H660GM-A board with MT7603 (2.4 GHz) and
MT7615/MT7663 (5 GHz).
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21326
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EN7528 shares the same clock/reset controller as EN7523. Enable
COMMON_CLK_EN7523 and RESET_CONTROLLER for ethernet hardware resets.
Update econet-eth driver and add it as default package.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21326
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
DASAN H660GM-A is a GPON ONT.
Specification:
- SoC: EcoNet EN7528
- RAM: 256 MB
- Flash: 256 MB SPI NAND
- Ethernet: 4x 1GbE
- FXS: 1 port
- GPON: 1 port
- USB: 1x USB 2.0
Install via OEM web UI:
1. Login to the factory web UI with username "superuser"
and password "Dz$!A!r7".
2. Rename the OpenWrt image
openwrt-econet-en7528-dasan_h660gm-a-squashfs-tclinux.trx
to G_ONU_openwrt.bin.
3. Upload the renamed image via the firmware upgrade page
at Maintenance > Firmware Upgrade in the factory web UI.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21326
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The EN7528 SoC uses a little endian MIPS architecture, unlike the big
endian EN751221 family. The tclinux TRX firmware format stores multi-byte
fields in the CPU's native byte order, requiring different header layouts
for each architecture:
- Big endian (EN751221): magic "2RDH", fields in big endian order
- Little endian (EN7528): magic "HDR2", fields in little endian order
Update tclinux-trx.sh to support both endianness variants:
- Add --endian parameter to select byte order (default: be)
- Add --model parameter for optional platform identifier field
- Convert to named parameters for clarity and extensibility
- Use hex32() helper for endian-aware 32-bit field output
Move TRX_ENDIAN configuration to subtarget files, allowing each subtarget
to specify its native byte order:
- en751221.mk: TRX_ENDIAN := be
- en7528.mk: TRX_ENDIAN := le
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21326
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Different vendor firmware versions use different BBT table sizes. The
checksum is calculated over the entire table, so the size must match
what the bootloader expects.
The Genexis Platinum-4410 bootloader was compiled with a BBT table
size of 250 entries (MAX_RAW_BAD_BLOCK_SIZE as found in vendor code).
Without this fix, the BBT checksum validation fails:
[ 0.391948] spi-nand spi0.0: Dosilicon SPI NAND was found.
[ 0.397651] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.407370] en75_bmt: found BMT in block 1023
[ 0.450160] en75_bmt: BBT not found and econet,can-write-factory-bbt is unset, giving up
Add a new DTS property 'econet,bbt-table-size' to configure the BBT
table size. If not specified, defaults to 1000.
After this patch:
[ 0.407021] en75_bmt: found BMT in block 1023
[ 0.449159] en75_bmt: found BBT in block 943
[ 0.453491] en75_bmt: BBT & BMT found
[ 0.457152] en75_bmt: blocks: total: 1024, user: 943, factory_bad: 0, worn: 0 reserve: 81
[ 0.465390] en75_bmt: 117 MiB usable space
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21326
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The EN7528 is a little endian dual-core MIPS 1004Kc SoC used in xPON
devices. Unlike the big endian EN751221, EN7528 uses the MIPS GIC
interrupt controller for SMP.
This adds minimal boot support for EN7528:
- New en7528 subtarget with mipsel architecture
- Kernel patches for EN7528 SoC with GIC support
- Timer driver extended to support GIC shared interrupts per CPU
- SPI driver fix for EN7528 chip select handling
- Generic device tree for initial bring-up
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21326
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix the function for reading the SerDes link status to work correctly
based on the code the SDK uses. This is mostly for the sake of
documentation and quick access to the information. The function isn't
used currently but may be in the future, thus no functional change here.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22014
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add 2500Base-X handling to mode setting which was rejected with
-ENOTSUPP before. SDK code available to us doesn't have the proper mode
value. Though by brute-forcing different mode values, 0x2d was found to
make a 2500Base-X link work.
This was tested with an otherwise correctly configured RTL8221B PHY
which is automatically switched between 2500Base-X and SGMII in the
upstream driver. Though, since there was a previous U-Boot setup for the
PHY in HISGMII mode, it may not be standalone yet.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22014
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
