mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2026-01-21 11:12:11 -05:00
realtek/rtl839x: Edgecore ECS4100-12PH support
Add support for the Edgecore ECS4100-12PH, an 8-port 802.3bt PoE Gigabit Ethernet switch with 2 combo RJ45/SFP and 2 SFP ports. Hardware: * SoC: RTL8393M * RAM: 256MiB * Flash: 32MiB SPI-NOR * Ethernet: * 8x GbE RJ45 PoE (external RTL8218B) * 2x GbE RJ45 / SFP combo (external RTL8214FC) * 2x SFP (external RTL8214FC) * Console: RJ45 RS232 port on front panel * PoE: Nuvoton M0516 + 2x Broadcom BCM59121 PSE Installation via bootloader: * open serial console (baud rate 115200) * interrupt boot process by pressing any key during boot * boot the OpenWrt initramfs: # rtk network on # tftpboot 0x8f000000 /tftpboot/openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-initramfs-kernel.bin # bootm * copy openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-squashfs-sysupgrade.bin to /tmp and use sysupgrade to install it: # sysupgrade /tmp/openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-squashfs-sysupgrade.bin Even though U-Boot claims the switch is based on the RTL8392M SoC, my device is based on the RTL8393M SoC. I have confirmed this by removing the heatsink, and the Linux kernel agrees with this. Therefore the DTS has the rtl8393_ prefix. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This commit is contained in:
Stijn Tintel
parent
7b351062d2
commit
fa9f925951
@ -51,6 +51,14 @@ realtek_setup_macs()
|
||||
local label_mac=""
|
||||
|
||||
case $board in
|
||||
edgecore,ecs4100-12ph|\
|
||||
tplink,sg2008p-v1|\
|
||||
tplink,sg2210p-v3|\
|
||||
tplink,sg2452p-v4|\
|
||||
tplink,t1600g-28ts-v3)
|
||||
label_mac=$(get_mac_label)
|
||||
lan_mac="$label_mac"
|
||||
;;
|
||||
hpe,1920-8g|\
|
||||
hpe,1920-8g-poe-65w|\
|
||||
hpe,1920-8g-poe-180w|\
|
||||
@ -75,13 +83,6 @@ realtek_setup_macs()
|
||||
lan_mac_start=skip
|
||||
lan_mac="$(get_mac_label)"
|
||||
;;
|
||||
tplink,sg2008p-v1|\
|
||||
tplink,sg2210p-v3|\
|
||||
tplink,sg2452p-v4|\
|
||||
tplink,t1600g-28ts-v3)
|
||||
label_mac=$(get_mac_label)
|
||||
lan_mac="$label_mac"
|
||||
;;
|
||||
tplink,tl-st1008f-v2|\
|
||||
zyxel,xgs1010-12-a1)
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
@ -132,6 +133,10 @@ realtek_setup_poe()
|
||||
ucidef_set_poe 193 "lan8 lan7 lan6 lan5 lan4 lan3 lan2 lan1 lan16 lan15 lan14 lan13 lan12 lan11 lan10 lan9 lan24 lan23
|
||||
lan22 lan21 lan20 lan19 lan18 lan17"
|
||||
;;
|
||||
edgecore,ecs4100-12ph|\
|
||||
netgear,gs110tpp-v1)
|
||||
ucidef_set_poe 130 "$(filter_port_list "$lan_list" "lan9 lan10")"
|
||||
;;
|
||||
engenius,ews2910p-v1|\
|
||||
engenius,ews2910p-v3)
|
||||
ucidef_set_poe 60 "$(filter_port_list "$lan_list" "lan9 lan10")"
|
||||
@ -153,9 +158,6 @@ realtek_setup_poe()
|
||||
lan22 lan21 lan20 lan19 lan18 lan17 lan32 lan31 lan30 lan29 lan28 lan27 lan26 lan25 lan40 lan39 lan38 lan37
|
||||
lan36 lan35 lan34 lan33 lan48 lan47 lan46 lan45 lan44 lan43 lan42 lan41"
|
||||
;;
|
||||
netgear,gs110tpp-v1)
|
||||
ucidef_set_poe 130 "$(filter_port_list "$lan_list" "lan9 lan10")"
|
||||
;;
|
||||
netgear,gs110tup-v1)
|
||||
ucidef_set_poe 240 "$(filter_port_list "$lan_list" "lan9 lan10")"
|
||||
;;
|
||||
|
||||
281
target/linux/realtek/dts/rtl8393_edgecore_ecs4100-12ph.dts
Normal file
281
target/linux/realtek/dts/rtl8393_edgecore_ecs4100-12ph.dts
Normal file
@ -0,0 +1,281 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
#include "rtl839x.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
compatible = "edgecore,ecs4100-12ph", "realtek,rtl839x-soc";
|
||||
model = "Edgecore ECS4100-12PH Switch";
|
||||
|
||||
aliases {
|
||||
label-mac-device = ðernet0;
|
||||
led-boot = &led_sys;
|
||||
led-failsafe = &led_sys;
|
||||
led-running = &led_sys;
|
||||
led-upgrade = &led_sys;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x10000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinmux_disable_sys_led>;
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_sys: sys {
|
||||
label = "green:sys";
|
||||
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-restart {
|
||||
compatible = "gpio-restart";
|
||||
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
i2c0: i2c-gpio-0 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
sfp0: sfp-p9 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c0>;
|
||||
los-gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
i2c1: i2c-gpio-1 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
sfp1: sfp-p10 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c1>;
|
||||
los-gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
i2c2: i2c-gpio-2 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
sfp2: sfp-p11 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c2>;
|
||||
los-gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpio1 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
i2c3: i2c-gpio-3 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
sfp3: sfp-p12 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c3>;
|
||||
los-gpio = <&gpio0 22 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
i2c4: i2c-gpio-4 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
lm75b@48 {
|
||||
compatible = "nxp,lm75a";
|
||||
reg = <0x48>;
|
||||
};
|
||||
|
||||
eeprom@56 {
|
||||
compatible = "atmel,24c32";
|
||||
reg = <0x56>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <1200>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet0 {
|
||||
nvmem-cells = <&macaddr_factory>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gpio0 {
|
||||
poe_enable {
|
||||
gpio-hog;
|
||||
gpios = <16 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
};
|
||||
|
||||
poe_reset {
|
||||
gpio-hog;
|
||||
gpios = <18 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_aux {
|
||||
status = "okay";
|
||||
|
||||
gpio1: expander@3 {
|
||||
compatible = "realtek,rtl8231";
|
||||
reg = <3>;
|
||||
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpio-ranges = <&gpio1 0 0 37>;
|
||||
|
||||
led-controller {
|
||||
compatible = "realtek,rtl8231-leds";
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus0 {
|
||||
reset-gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <2000>;
|
||||
reset-post-delay-us = <140000>;
|
||||
|
||||
/* External phy RTL8218B */
|
||||
EXTERNAL_PHY(0)
|
||||
EXTERNAL_PHY(1)
|
||||
EXTERNAL_PHY(2)
|
||||
EXTERNAL_PHY(3)
|
||||
EXTERNAL_PHY(4)
|
||||
EXTERNAL_PHY(5)
|
||||
EXTERNAL_PHY(6)
|
||||
EXTERNAL_PHY(7)
|
||||
|
||||
/* External phy RTL8214FC */
|
||||
EXTERNAL_SFP_PHY_FULL(48, 0)
|
||||
EXTERNAL_SFP_PHY_FULL(49, 1)
|
||||
EXTERNAL_SFP_PHY_FULL(50, 2)
|
||||
EXTERNAL_SFP_PHY_FULL(51, 3)
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@100000 {
|
||||
compatible = "u-boot,env";
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x20000>;
|
||||
};
|
||||
partition@120000 {
|
||||
label = "empty";
|
||||
reg = <0x120000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
partition@180000 {
|
||||
label = "para";
|
||||
reg = <0x180000 0x20000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
partition@200000 {
|
||||
label = "firmware";
|
||||
reg = <0x200000 0xdf0000>;
|
||||
compatible = "openwrt,uimage", "denx,uimage";
|
||||
};
|
||||
partition@ff0000 {
|
||||
label = "certificates";
|
||||
reg = <0xff0000 0x10000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
SWITCH_PORT_SDS(0, 1, 0, qsgmii)
|
||||
SWITCH_PORT_SDS(1, 2, 0, qsgmii)
|
||||
SWITCH_PORT_SDS(2, 3, 0, qsgmii)
|
||||
SWITCH_PORT_SDS(3, 4, 0, qsgmii)
|
||||
SWITCH_PORT_SDS(4, 5, 1, qsgmii)
|
||||
SWITCH_PORT_SDS(5, 6, 1, qsgmii)
|
||||
SWITCH_PORT_SDS(6, 7, 1, qsgmii)
|
||||
SWITCH_PORT_SDS(7, 8, 1, qsgmii)
|
||||
|
||||
SWITCH_PORT_SDS(48, 9, 12, qsgmii)
|
||||
SWITCH_PORT_SDS(49, 10, 12, qsgmii)
|
||||
SWITCH_PORT_SDS(50, 11, 12, qsgmii)
|
||||
SWITCH_PORT_SDS(51, 12, 12, qsgmii)
|
||||
|
||||
port@52 {
|
||||
ethernet = <ðernet0>;
|
||||
reg = <52>;
|
||||
phy-mode = "internal";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -9,6 +9,21 @@ define Device/d-link_dgs-1210-52
|
||||
endef
|
||||
TARGET_DEVICES += d-link_dgs-1210-52
|
||||
|
||||
define Device/edgecore_ecs4100-12ph
|
||||
$(Device/uimage-rt-loader)
|
||||
SOC := rtl8393
|
||||
DEVICE_VENDOR := Edgecore
|
||||
DEVICE_MODEL := ECS4100-12PH
|
||||
IMAGE_SIZE := 14336k
|
||||
DEVICE_PACKAGES := \
|
||||
kmod-eeprom-at24 \
|
||||
kmod-hwmon-adt7470 \
|
||||
kmod-hwmon-lm75 \
|
||||
kmod-thermal \
|
||||
realtek-poe
|
||||
endef
|
||||
TARGET_DEVICES += edgecore_ecs4100-12ph
|
||||
|
||||
define Device/hpe_1920-48g
|
||||
$(Device/hpe_1920)
|
||||
SOC := rtl8393
|
||||
|
||||
Loading…
Reference in New Issue
Block a user