mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-11-04 06:54:27 -05:00
ath79: Add support for OpenMesh OM2P v4
Device specifications:
======================
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 1
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[wrap two very long lines, fix typo in comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Sven Eckelmann
Adrian Schmutzler
parent
e1938d3397
commit
dd1d95cb03
@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk
|
||||
PKG_NAME:=uboot-envtools
|
||||
PKG_DISTNAME:=u-boot
|
||||
PKG_VERSION:=2020.04
|
||||
PKG_RELEASE:=9
|
||||
PKG_RELEASE:=10
|
||||
|
||||
PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2
|
||||
PKG_SOURCE_URL:= \
|
||||
|
||||
@ -85,6 +85,7 @@ netgear,wndr4300tn|\
|
||||
netgear,wndr4300sw)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000"
|
||||
;;
|
||||
openmesh,om2p-v4|\
|
||||
plasmacloud,pa300|\
|
||||
plasmacloud,pa300e)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x40000"
|
||||
|
||||
8
target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts
Normal file
8
target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts
Normal file
@ -0,0 +1,8 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca9533_openmesh_om2p-v4.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "openmesh,om2p-v4", "qca,qca9533";
|
||||
model = "OpenMesh OM2P v4";
|
||||
};
|
||||
157
target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi
Normal file
157
target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi
Normal file
@ -0,0 +1,157 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
/delete-property/ bootargs;
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_blue;
|
||||
led-failsafe = &led_power_blue;
|
||||
led-running = &led_power_blue;
|
||||
led-upgrade = &led_power_blue;
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_blue: power_blue {
|
||||
label = "blue:power";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wifi_green {
|
||||
label = "green:wifi";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wifi_yellow {
|
||||
label = "yellow:wifi";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi_red {
|
||||
label = "red:wifi";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_blue {
|
||||
label = "blue:wan";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan_blue {
|
||||
label = "blue:lan";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
/* hw_margin_ms is actually 300s but driver limits it to 60s */
|
||||
hw_margin_ms = <60000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
/* partitions are passed via bootloader */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x040000>;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "custom";
|
||||
reg = <0x080000 0x140000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "inactive";
|
||||
reg = <0x1c0000 0x700000>;
|
||||
};
|
||||
|
||||
partition@8c0000 {
|
||||
label = "inactive2";
|
||||
reg = <0x8c0000 0x700000>;
|
||||
};
|
||||
|
||||
art: partition@fc0000 {
|
||||
label = "ART";
|
||||
reg = <0xfc0000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy4>;
|
||||
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
/* Workaround: keep the Ethernet interfaces order/mapping correct
|
||||
* (GMAC0 -> eth0, GMAC1 -> eth1, same as in old ar71xx target)
|
||||
*/
|
||||
compatible = "qca,qca9530-eth", "syscon", "simple-mfd";
|
||||
|
||||
mtd-mac-address = <&art 0x6>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
};
|
||||
@ -230,6 +230,10 @@ netgear,wnr2200-16m)
|
||||
ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "amber:lan3" "switch0" "0x08" "0x02"
|
||||
ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "amber:lan4" "switch0" "0x10" "0x02"
|
||||
;;
|
||||
openmesh,om2p-v4)
|
||||
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0"
|
||||
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
|
||||
;;
|
||||
pcs,cr3000)
|
||||
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
|
||||
ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x04"
|
||||
|
||||
@ -152,6 +152,7 @@ ath79_setup_interfaces()
|
||||
comfast,cf-e120a-v3|\
|
||||
comfast,cf-e314n-v2|\
|
||||
compex,wpj531-16m|\
|
||||
openmesh,om2p-v4|\
|
||||
plasmacloud,pa300|\
|
||||
plasmacloud,pa300e|\
|
||||
tplink,cpe210-v1|\
|
||||
|
||||
112
target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh
Normal file
112
target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh
Normal file
@ -0,0 +1,112 @@
|
||||
# The U-Boot loader of the OpenMesh devices requires image sizes and
|
||||
# checksums to be provided in the U-Boot environment.
|
||||
# The OpenMesh devices come with 2 main partitions - while one is active
|
||||
# sysupgrade will flash the other. The boot order is changed to boot the
|
||||
# newly flashed partition. If the new partition can't be booted due to
|
||||
# upgrade failures the previously used partition is loaded.
|
||||
|
||||
cfg_value_get()
|
||||
{
|
||||
local cfg=$1 cfg_opt
|
||||
local section=$2 our_section=0
|
||||
local param=$3 our_param=
|
||||
|
||||
for cfg_opt in $cfg; do
|
||||
[ "$cfg_opt" = "[$section]" ] && our_section=1 && continue
|
||||
[ "$our_section" = "1" ] || continue
|
||||
|
||||
our_param=${cfg_opt%%=*}
|
||||
[ "$param" = "$our_param" ] && echo ${cfg_opt##*=} && break
|
||||
done
|
||||
}
|
||||
|
||||
platform_do_upgrade_openmesh()
|
||||
{
|
||||
local img_path="$1"
|
||||
local restore_backup
|
||||
|
||||
local setenv_script="/tmp/fw_env_upgrade"
|
||||
|
||||
local inactive_mtd="$(find_mtd_index $PART_NAME)"
|
||||
local inactive_offset="$(cat /sys/class/mtd/mtd${inactive_mtd}/offset)"
|
||||
local total_size="$(cat /sys/class/mtd/mtd${inactive_mtd}/size)"
|
||||
local flash_start_mem=0x9f000000
|
||||
local data_offset=$((64 * 1024))
|
||||
|
||||
# detect to which flash region the new image is written to.
|
||||
#
|
||||
# 1. check what is the mtd index for the first flash region on this
|
||||
# device
|
||||
# 2. check if the target partition ("inactive") has the mtd index of
|
||||
# the first flash region
|
||||
#
|
||||
# - when it is: the new bootseq will be 1,2 and the first region is
|
||||
# modified
|
||||
# - when it isn't: bootseq will be 2,1 and the second region is
|
||||
# modified
|
||||
#
|
||||
# The detection has to be done via the hardcoded mtd partition because
|
||||
# the current boot might be done with the fallback region. Let us
|
||||
# assume that the current bootseq is 1,2. The bootloader detected that
|
||||
# the image in flash region 1 is corrupt and thus switches to flash
|
||||
# region 2. The bootseq in the u-boot-env is now still the same and
|
||||
# the sysupgrade code can now only rely on the actual mtd indexes and
|
||||
# not the bootseq variable to detect the currently booted flash
|
||||
# region/image.
|
||||
#
|
||||
# In the above example, an implementation which uses bootseq ("1,2") to
|
||||
# detect the currently booted image would assume that region 1 is booted
|
||||
# and then overwrite the variables for the wrong flash region (aka the
|
||||
# one which isn't modified). This could result in a device which doesn't
|
||||
# boot anymore to Linux until it was reflashed with ap51-flash.
|
||||
local next_boot_part="1"
|
||||
local primary_kernel_mtd="3"
|
||||
[ "$inactive_mtd" = "$primary_kernel_mtd" ] || next_boot_part="2"
|
||||
|
||||
local cfg_size=$(dd if="$img_path" bs=2 skip=35 count=4 2>/dev/null)
|
||||
local cfg_length=$((0x$cfg_size))
|
||||
local cfg_content=$(dd if="$img_path" bs=1 skip=$data_offset count=$cfg_length 2>/dev/null)
|
||||
|
||||
local kernel_size=$(dd if="$img_path" bs=2 skip=71 count=4 2>/dev/null)
|
||||
local kernel_length=$((0x$kernel_size))
|
||||
local kernel_md5=$(cfg_value_get "$cfg_content" "vmlinux" "md5sum")
|
||||
|
||||
local rootfs_size=$(dd if="$img_path" bs=2 skip=107 count=4 2>/dev/null)
|
||||
local rootfs_length=$((0x$rootfs_size))
|
||||
local rootfs_md5=$(cfg_value_get "$cfg_content" "rootfs" "md5sum")
|
||||
local rootfs_checksize=$(cfg_value_get "$cfg_content" "rootfs" "checksize")
|
||||
|
||||
# take care of restoring a saved config
|
||||
[ -n "$UPGRADE_BACKUP" ] && restore_backup="${MTD_CONFIG_ARGS} -j ${UPGRADE_BACKUP}"
|
||||
|
||||
# write image parts
|
||||
mtd -q erase inactive
|
||||
dd if="$img_path" bs=1 skip=$((data_offset + cfg_length + kernel_length)) count=$rootfs_length 2>&- | \
|
||||
mtd -n -p $kernel_length $restore_backup write - $PART_NAME
|
||||
dd if="$img_path" bs=1 skip=$((data_offset + cfg_length)) count=$kernel_length 2>&- | \
|
||||
mtd -n write - $PART_NAME
|
||||
|
||||
# prepare new u-boot env
|
||||
if [ "$next_boot_part" = "1" ]; then
|
||||
echo "bootseq 1,2" > $setenv_script
|
||||
else
|
||||
echo "bootseq 2,1" > $setenv_script
|
||||
fi
|
||||
|
||||
printf "kernel_size_%i %i\n" $next_boot_part $((kernel_length / 1024)) >> $setenv_script
|
||||
printf "vmlinux_start_addr 0x%08x\n" $((flash_start_mem + inactive_offset)) >> $setenv_script
|
||||
printf "vmlinux_size 0x%08x\n" ${kernel_length} >> $setenv_script
|
||||
printf "vmlinux_checksum %s\n" ${kernel_md5} >> $setenv_script
|
||||
|
||||
printf "rootfs_size_%i %i\n" $next_boot_part $(((total_size-kernel_length) / 1024)) >> $setenv_script
|
||||
printf "rootfs_start_addr 0x%08x\n" $((flash_start_mem+inactive_offset+kernel_length)) >> $setenv_script
|
||||
printf "rootfs_size %s\n" $rootfs_checksize >> $setenv_script
|
||||
printf "rootfs_checksum %s\n" ${rootfs_md5} >> $setenv_script
|
||||
|
||||
# store u-boot env changes
|
||||
mkdir -p /var/lock
|
||||
fw_setenv -s $setenv_script || {
|
||||
echo "failed to update U-Boot environment"
|
||||
return 1
|
||||
}
|
||||
}
|
||||
@ -50,6 +50,10 @@ platform_do_upgrade() {
|
||||
jjplus,ja76pf2)
|
||||
redboot_fis_do_upgrade "$1" linux
|
||||
;;
|
||||
openmesh,om2p-v4)
|
||||
PART_NAME="inactive"
|
||||
platform_do_upgrade_openmesh "$1"
|
||||
;;
|
||||
plasmacloud,pa300|\
|
||||
plasmacloud,pa300e)
|
||||
PART_NAME="inactive"
|
||||
|
||||
@ -1557,6 +1557,26 @@ define Device/ocedo_ursus
|
||||
endef
|
||||
TARGET_DEVICES += ocedo_ursus
|
||||
|
||||
define Device/openmesh_om2p-common
|
||||
DEVICE_VENDOR := OpenMesh
|
||||
DEVICE_PACKAGES := uboot-envtools
|
||||
IMAGE_SIZE := 7168k
|
||||
BLOCKSIZE := 256k
|
||||
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
|
||||
pad-to $$(BLOCKSIZE)
|
||||
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
||||
openmesh-image ce_type=OM2P | append-metadata
|
||||
endef
|
||||
|
||||
define Device/openmesh_om2p-v4
|
||||
$(Device/openmesh_om2p-common)
|
||||
SOC := qca9533
|
||||
DEVICE_MODEL := OM2P
|
||||
DEVICE_VARIANT := v4
|
||||
SUPPORTED_DEVICES += om2pv4
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_om2p-v4
|
||||
|
||||
define Device/openmesh_om5p-ac-v2
|
||||
SOC := qca9558
|
||||
DEVICE_VENDOR := OpenMesh
|
||||
|
||||
Loading…
Reference in New Issue
Block a user