mirror of
git://git.openwrt.org/openwrt/openwrt.git
synced 2025-12-08 13:42:10 -05:00
ipq40xx: add support for ASUS Lyra Mini (MAP-AC1300)
The device is the little brother of the already supported ASUS Lyra but
with the flash configuration/layout of the RT-AC58U.
Hardware
--------
SOC: Qualcomm IPQ4019
FLASH: 2MB (Macronix MX25L1606E)
128MB (GigaDevice GD5F1GQ4UCYIG)
RAM: 256MB (Nanya NT5CC128M16IP-DI)
WIFI: Qualcomm IPQ4019
BT: Atheros AR3012-BL3D
ETH: 1x WAN, 1x LAN
LED: 1 RBG LED
BTN: WPS, Reset
UART: 115200 8N1 (square pin = VCC) VCC-TX-RX-GND
MAC addresses
-------------
LAN 2.4G + 1
WAN 2.4G + 3
2.4G Label MAC (stored in factory offset 0x1006)
5G 2.4G + 2 (stored in factory offset 0x5006)
Installation
------------
SSH
---
1. Reset the device, setup and enable SSH.
2. Transfer initramfs.itb to /tmp on the device.
3. SSH into the router, credentials are the same as in the web ui.
4. Write initramfs to linux partition:
mtd-write -d linux -i initramfs.itb
5. Reboot and wait for OpenWrt to boot.
6. Transfer sysupgrade.bin to /tmp on the device.
7. SSH into the router, user root, no pw.
8. Delete jffs2 ubi partition:
ubirmvol /dev/ubi0 --name=jffs2
9. Flash OpenWrt:
sysupgrade -n sysupgrade.bin
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20573
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
Christoph Krapp
Robert Marko
parent
b915eba9a9
commit
120b70a6e2
@ -31,6 +31,7 @@ ipq40xx_setup_interfaces()
|
||||
;;
|
||||
8dev,jalapeno|\
|
||||
alfa-network,ap120c-ac|\
|
||||
asus,map-ac1300|\
|
||||
asus,map-ac2200|\
|
||||
cilab,meshpoint-one|\
|
||||
edgecore,ecw5211|\
|
||||
|
||||
@ -6,6 +6,7 @@ RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||
|
||||
platform_check_image() {
|
||||
case "$(board_name)" in
|
||||
asus,map-ac1300|\
|
||||
asus,rt-ac42u|\
|
||||
asus,rt-ac58u)
|
||||
local ubidev=$(nand_find_ubi $CI_UBIPART)
|
||||
@ -140,6 +141,7 @@ platform_do_upgrade() {
|
||||
fi
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
asus,map-ac1300|\
|
||||
asus,map-ac2200|\
|
||||
asus,rt-ac42u|\
|
||||
asus,rt-ac58u)
|
||||
|
||||
@ -0,0 +1,405 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "ASUS Lyra Mini MAP-AC1300";
|
||||
compatible = "asus,map-ac1300";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_blue0;
|
||||
led-failsafe = &led_red0;
|
||||
led-running = &led_blue0;
|
||||
led-upgrade = &led_red0;
|
||||
ethernet1 = &swport4;
|
||||
label-mac-device = &wifi0;
|
||||
};
|
||||
|
||||
soc {
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>,
|
||||
<&tlmm 1 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
/*
|
||||
* U-boot looks for "n25q128a11" node,
|
||||
* if we don't have it, it will spit out the following warning:
|
||||
* "ipq: fdt fixup unable to find compatible node".
|
||||
*/
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
linux,modalias = "m25p80", "mx25l1606e", "n25q128a11";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
partition@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition@e0000 {
|
||||
label = "APPSBLENV"; /* uboot env*/
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition@f0000 {
|
||||
label = "APPSBL"; /* uboot */
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
partition@170000 {
|
||||
label = "ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
/* 0x00180000 - 0x00200000 unused */
|
||||
};
|
||||
};
|
||||
|
||||
spi-nand@1 {
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
compatible = "linux,ubi";
|
||||
reg = <0x00000000 0x08000000>;
|
||||
label = "ubi";
|
||||
|
||||
volumes {
|
||||
ubi_factory: ubi-volume-factory {
|
||||
volname = "Factory";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ubi_factory {
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
precal_factory_1000: precal@1000 {
|
||||
reg = <0x1000 0x2f20>;
|
||||
};
|
||||
|
||||
macaddr_factory_1006: macaddr@1006 {
|
||||
reg = <0x1006 0x6>;
|
||||
};
|
||||
|
||||
precal_factory_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
|
||||
macaddr_factory_5006: macaddr@5006 {
|
||||
reg = <0x5006 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
i2c_0_pins: i2c_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_i2c0";
|
||||
pins = "gpio58", "gpio59";
|
||||
drive-strength = <16>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
mux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
mux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54", "gpio1";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
nvmem-cells = <&precal_factory_1000>;
|
||||
qcom,ath10k-calibration-variant = "ASUS-MAP-AC1300";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
nvmem-cells = <&precal_factory_5000>;
|
||||
qcom,ath10k-calibration-variant = "ASUS-MAP-AC1300";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
/* Bluetooth module attached via USB */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_i2c3 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&i2c_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led-controller@32 {
|
||||
/* 9-channel RGB LED controller */
|
||||
compatible = "national,lp5523";
|
||||
reg = <0x32>;
|
||||
clock-mode = /bits/ 8 <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/*
|
||||
* There is only one single extremely bright RGB-LED.
|
||||
* The RGB-color channels are running in parallel to
|
||||
* increase the current delivery capabilities beyond
|
||||
* what a single PWM-output of the controller can do.
|
||||
*/
|
||||
|
||||
led_blue0: led@0 {
|
||||
chan-name = "blue-0";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <0>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function-enumerator = <0>;
|
||||
};
|
||||
|
||||
led@1 {
|
||||
chan-name = "blue-1";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <1>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function-enumerator = <1>;
|
||||
};
|
||||
|
||||
led@2 {
|
||||
chan-name = "blue-2";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <2>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function-enumerator = <2>;
|
||||
};
|
||||
|
||||
led_green0: led@3 {
|
||||
chan-name = "green-0";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <3>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function-enumerator = <0>;
|
||||
};
|
||||
|
||||
led@4 {
|
||||
chan-name = "green-1";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <4>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function-enumerator = <1>;
|
||||
};
|
||||
|
||||
led@5 {
|
||||
chan-name = "green-2";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <5>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function-enumerator = <2>;
|
||||
};
|
||||
|
||||
led_red0: led@6 {
|
||||
chan-name = "red-0";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <6>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function-enumerator = <0>;
|
||||
};
|
||||
|
||||
led@7 {
|
||||
chan-name = "red-1";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <7>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function-enumerator = <1>;
|
||||
};
|
||||
|
||||
led@8 {
|
||||
chan-name = "red-2";
|
||||
led-cur = /bits/ 8 <0x80>;
|
||||
max-cur = /bits/ 8 <0xff>;
|
||||
reg = <8>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function-enumerator = <2>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_factory_1006 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&swport4 {
|
||||
status = "okay";
|
||||
|
||||
label = "wan";
|
||||
nvmem-cells = <&macaddr_factory_1006 3>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&swport5 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan";
|
||||
};
|
||||
@ -189,6 +189,15 @@ define Device/aruba_ap-365
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-365
|
||||
|
||||
define Device/asus_map-ac1300
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := Lyra Mini (MAP-AC1300)
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_PACKAGES := kmod-ath3k
|
||||
endef
|
||||
TARGET_DEVICES += asus_map-ac1300
|
||||
|
||||
define Device/asus_map-ac2200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
|
||||
Loading…
Reference in New Issue
Block a user